5秒后页面跳转
VNCLO-PSU-US PDF预览

VNCLO-PSU-US

更新时间: 2024-10-28 06:02:23
品牌 Logo 应用领域
飞特帝亚 - FTDI /
页数 文件大小 规格书
25页 702K
描述
Vinculo Development Module

VNCLO-PSU-US 数据手册

 浏览型号VNCLO-PSU-US的Datasheet PDF文件第4页浏览型号VNCLO-PSU-US的Datasheet PDF文件第5页浏览型号VNCLO-PSU-US的Datasheet PDF文件第6页浏览型号VNCLO-PSU-US的Datasheet PDF文件第8页浏览型号VNCLO-PSU-US的Datasheet PDF文件第9页浏览型号VNCLO-PSU-US的Datasheet PDF文件第10页 
Document Reference No.: FT_000327  
Vinculo Development Module Datasheet Version 1.0  
Clearance No.: FTDI#173  
2 Functionality  
2.1 Power  
The Vinculo requires +5V for the USB host ports to power USB devices from the module. This is further  
regulated to +3.3V for VNC2.  
A +9V/1A DC supply is also available which can be used as an AC-DC adapter (wall-wart). The +9V is  
regulated to +5V and +3V3 on the Vinculo module.  
As an alternative to the AC-DC adapter the on board regulators can be taken out of circuit with jumpers  
to allow the +5V from a USB host port to power the module. Care should be taken with this approach as  
a USB host port can only provide a maximum of 500mA, which must power the Vinculo and potentially  
any devices connected to the Vinculo.  
The +5V and +3V3 supplies may also be accessed on the J1 header pins.  
VNC2 requires between 8 and 24mA depending on the clock speed at which the VNC2 core is running.  
2.2 Input/Output  
Due to the flexibility of the VNC2 IC the actual definition of each pin is not fixed. The firmware developed  
for any application can use the VNC2 IO Mux to route a signal, e.g. UART TXD, to a range of IO pins. An  
IOMux utility built into the free tool chain development environment, IDE, allows the developer to define  
the IO from a GUI interface. The utility will then convert the users IO selection into C code to be included  
as part of the project firmware...  
There are 38 configurable IO pins available to the user, 8 of which are reserved for connecting to the  
onboard ADC device. The other 30 pins may be used for GPIO, UART, SPI or FIFO connectivity depending  
on the interface of the shield designed to connect to the Vinculo module.  
There are 2 USB ports on the Vinculo. The firmware will determine if the port is configured for USB host  
operation or USB device operation.  
2.3 LEDs  
There are 3 LEDs on Vinculo.  
LED1 is driven by the VNC2-64Q IC depending on which firmware is loaded. It may be used to indicate  
traffic on the USB slave port connected via CN3.  
LED2 is driven by the VNC2-64Q IC depending on which firmware is loaded. It may be used to indicate  
traffic on the USB host port connected via CN2.  
LED3 is driven by the 3V3 supply connected to the VNC2-64Q IC. It will indicate when the Vinculo module  
is powered.  
Copyright © 2010 Future Technology Devices International Limited  
3

与VNCLO-PSU-US相关器件

型号 品牌 获取价格 描述 数据表
VNCLO-SHLD1A FTDI

获取价格

Vinculo Development Module
VND05 STMICROELECTRONICS

获取价格

ISO HIGH SIDE SMART POWER SOLID STATE RELAY
VND05B STMICROELECTRONICS

获取价格

DOUBLE CHANNEL HIGH SIDE SMART POWER SOLID STATE RELAY
VND05B(011Y) STMICROELECTRONICS

获取价格

1.6A BUF OR INV BASED PRPHL DRVR, PZFM7, HORIZONTAL, HEPTAWATT-7
VND05B011Y STMICROELECTRONICS

获取价格

DOUBLE CHANNEL HIGH SIDE SMART POWER SOLID STATE RELAY
VND05B012Y STMICROELECTRONICS

获取价格

DOUBLE CHANNEL HIGH SIDE SMART POWER SOLID STATE RELAY
VND05B-E STMICROELECTRONICS

获取价格

DOUBLE CHANNEL HIGH SIDE SMART POWER SOLID STATE RELAY
VND05BSP STMICROELECTRONICS

获取价格

ISO HIGH SIDE SMART POWER SOLID STATE RELAY
VND05BSP_05 STMICROELECTRONICS

获取价格

Iso high side smart power solid state relay
VND05BSP13TR STMICROELECTRONICS

获取价格

BUF OR INV BASED PRPHL DRVR, PDSO10, ROHS COMPLIANT, SO-10