5秒后页面跳转
SSTU32864 PDF预览

SSTU32864

更新时间: 2024-11-05 06:14:23
品牌 Logo 应用领域
恩智浦 - NXP 双倍数据速率
页数 文件大小 规格书
21页 116K
描述
1.8 V configurable registered buffer for DDR2 RDIMM applications

SSTU32864 数据手册

 浏览型号SSTU32864的Datasheet PDF文件第2页浏览型号SSTU32864的Datasheet PDF文件第3页浏览型号SSTU32864的Datasheet PDF文件第4页浏览型号SSTU32864的Datasheet PDF文件第5页浏览型号SSTU32864的Datasheet PDF文件第6页浏览型号SSTU32864的Datasheet PDF文件第7页 
SSTU32864  
1.8 V configurable registered buffer for DDR2 RDIMM  
applications  
Rev. 02 — 22 October 2004  
Product data sheet  
1. General description  
The SSTU32864 is a 25-bit 1:1 or 14-bit 1:2 configurable registered buffer designed for  
1.7 V to 1.9 V VDD operation.  
All clock and data inputs are compatible with the JEDEC standard for SSTL_18. The  
control inputs are LVCMOS. All outputs are 1.8 V CMOS drivers that have been optimized  
to drive the DDR2 DIMM load.  
The SSTU32864 operates from a differential clock (CK and CK). Data are registered at  
the crossing of CK going HIGH, and CK going LOW.  
The C0 input controls the pinout configuration of the 1:2 pinout from A configuration (when  
LOW) to B configuration (when HIGH). The C1 input controls the pinout configuration from  
25-bit 1:1 (when LOW) to 14-bit 1:2 (when HIGH).  
The device supports low-power standby operation. When the reset input (RESET) is LOW,  
the differential input receivers are disabled, and undriven (floating) data, clock and  
reference voltage (VREF) inputs are allowed. In addition, when RESET is LOW all registers  
are reset, and all outputs are forced LOW. The LVCMOS RESET and Cn inputs must  
always be held at a valid logic HIGH or LOW level.  
To ensure defined outputs from the register before a stable clock has been supplied,  
RESET must be held in the LOW state during power-up.  
In the DDR2 RDIMM application, RESET is specified to be completely asynchronous with  
respect to CK and CK. Therefore, no timing relationship can be guaranteed between the  
two. When entering reset, the register will be cleared and the data outputs will be driven  
LOW quickly, relative to the time to disable the differential input receivers. However, when  
coming out of reset, the register will become active quickly, relative to the time to enable  
the differential input receivers. As long as the data inputs are LOW, and the clock is stable  
during the time from the LOW-to-HIGH transition of RESET until the input receivers are  
fully enabled, the design of the SSTU32864 must ensure that the outputs will remain  
LOW, thus ensuring no glitches on the output.  
The device monitors both DCS and CSR inputs and will gate the Qn outputs from  
changing states when both DCS and CSR inputs are HIGH. If either DCS or CSR input is  
LOW, the Qn outputs will function normally. The RESET input has priority over the DCS  
and CSR control and will force the outputs LOW. If the DCS-control functionality is not  
desired, then the CSR input can be hardwired to ground, in which case the setup time  
requirement for DCS would be the same as for the other Dn data inputs.  
The SSTU32864 is available in a 96-ball, low profile fine-pitch ball grid array (LFBGA96)  
package.  

与SSTU32864相关器件

型号 品牌 获取价格 描述 数据表
SSTU32864EC NXP

获取价格

1.8 V configurable registered buffer for DDR2 RDIMM applications
SSTU32864EC,518 NXP

获取价格

SSTU32864 - 1.8 V configurable registered buffer for DDR2 RDIMM applications BGA 96-Pin
SSTU32864EC/G NXP

获取价格

1.8 V configurable registered buffer for DDR2 RDIMM applications
SSTU32864EC/G,518 NXP

获取价格

SSTU32864 - 1.8 V configurable registered buffer for DDR2 RDIMM applications BGA 96-Pin
SSTU32864HT IDT

获取价格

Interface Circuit
SSTU32865 NXP

获取价格

1.8 V 28-bit 1:2 registered buffer with parity for DDR2 RDIMM
SSTU32865EG NXP

获取价格

1.8 V 28-bit 1:2 registered buffer with parity for DDR2 RDIMM
SSTU32865ET NXP

获取价格

1.8 V 28-bit 1:2 registered buffer with parity for DDR2 RDIMM
SSTU32865ET,518 NXP

获取价格

SSTU32865 - 1.8 V 28-bit 1:2 registered buffer with parity for DDR2 RDIMM applications BGA
SSTU32865ET,557 NXP

获取价格

SSTU32865 - 1.8 V 28-bit 1:2 registered buffer with parity for DDR2 RDIMM applications BGA