SiSS46DN
Vishay Siliconix
www.vishay.com
N-Channel 100 V (D-S) MOSFET
FEATURES
PowerPAK® 1212-8S
D
8
• TrenchFET® Gen IV power MOSFET
• Very low RDS - Qg figure-of-merit (FOM)
• Tuned for the lowest RDS - Qoss FOM
• 100 % Rg and UIS tested
D
7
D
6
D
5
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
1
S
2
S
3
S
4
G
1
D
APPLICATIONS
Top View
Bottom View
• Synchronous rectification
• Primary side switch
PRODUCT SUMMARY
VDS (V)
100
0.0128
0.0146
21.5
• DC/DC converter
• Solar micro inverter
• Motor drive switch
• Battery and load switch
• Industrial
G
RDS(on) max. () at VGS = 10 V
RDS(on) max. () at VGS = 7.5 V
Qg typ. (nC)
S
ID (A)
45.3
N-Channel MOSFET
Configuration
Single
ORDERING INFORMATION
Package
PowerPAK 1212-8S
SiSS46DN-T1-GE3
Lead (Pb)-free and halogen-free
ABSOLUTE MAXIMUM RATINGS (TA = 25 °C, unless otherwise noted)
PARAMETER
SYMBOL
LIMIT
100
UNIT
Drain-source voltage
Gate-source voltage
VDS
V
VGS
20
TC = 25 °C
45.3
TC = 70 °C
TA = 25 °C
TA = 70 °C
36.2
Continuous drain current (TJ = 150 °C)
ID
12.5 b, c
10 b, c
100
A
Pulsed drain current (t = 100 μs)
IDM
IS
TC = 25 °C
59.7
4.5 b, c
Continuous source-drain diode current
TA = 25 °C
Single pulse avalanche current
Single pulse avalanche energy
IAS
20
L = 0.1 mH
EAS
20
mJ
W
TC = 25 °C
TC = 70 °C
TA = 25 °C
TA = 70 °C
65.7
42
Maximum power dissipation
PD
5 b, c
3.2 b, c
-55 to +150
260
Operating junction and storage temperature range
Soldering recommendations (peak temperature) c
TJ, Tstg
°C
THERMAL RESISTANCE RATINGS
PARAMETER
Maximum junction-to-ambient b
SYMBOL
RthJA
TYPICAL
20
MAXIMUM
UNIT
t 10 s
Steady state
25
°C/W
Maximum junction-to-case (drain)
RthJC
1.5
1.9
Notes
a. Package limited
b. Surface mounted on 1" x 1" FR4 board
c. t = 10 s
d. See solder profile (www.vishay.com/doc?73257). The PowerPAK 1212-8S is a leadless package. The end of the lead terminal is exposed
copper (not plated) as a result of the singulation process in manufacturing. A solder fillet at the exposed copper tip cannot be guaranteed
and is not required to ensure adequate bottom side solder interconnection
e. Rework conditions: manual soldering with a soldering iron is not recommended for leadless components
f. Maximum under steady state conditions is 63 °C/W
g. TC = 25 °C
S18-0728-Rev. A, 23-Jul-2018
Document Number: 77881
1
For technical questions, contact: pmostechsupport@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000