SiSS5112DN
Vishay Siliconix
www.vishay.com
N-Channel 100 V (D-S) MOSFET
FEATURES
PowerPAK® 1212-8S
D
8
• TrenchFET® Gen V power MOSFET
• Very low RDS x Qg figure-of-merit (FOM)
• Tuned for the lowest RDS x Qoss FOM
• 100 % Rg and UIS tested
D
7
D
6
D
5
• Material categorization: for definitions of
compliance please see www.vishay.com/doc?99912
1
S
2
S
3
S
4
G
1
D
APPLICATIONS
Top View
Bottom View
• Synchronous rectification
• Primary side switch
• DC/DC converters
PRODUCT SUMMARY
VDS (V)
RDS(on) max. () at VGS = 10 V
RDS(on) max. () at VGS = 7.5 V
Qg typ. (nC)
100
0.0149
0.0185
8
G
• Power supplies
• Motor drive control
N-Channel MOSFET
ID (A) a
40.7
S
Configuration
Single
ORDERING INFORMATION
Package
Lead (Pb)-free and halogen-free
PowerPAK 1212-8S
SiSS5112DN-T1-GE3
ABSOLUTE MAXIMUM RATINGS (TA = 25 °C, unless otherwise noted)
PARAMETER
Drain-source voltage
Gate-source voltage
SYMBOL
LIMIT
100
UNIT
VDS
V
VGS
20
TC = 25 °C
40.7
TC = 70 °C
TA = 25 °C
TA = 70 °C
32.6
Continuous drain current (TJ = 150 °C)
ID
11 b, c
8.8 b, c
70
A
Pulsed drain current (t = 100 μs)
IDM
IS
TC = 25 °C
47.3
3.4 b, c
Continuous source-drain diode current
TA = 25 °C
L = 0.1 mH
TC = 25 °C
Single pulse avalanche current
Single pulse avalanche energy
IAS
20
EAS
20
mJ
W
52
TC = 70 °C
33.3
Maximum power dissipation
PD
TA = 25 °C
TA = 70 °C
3.7 b, c
2.4 b, c
-55 to +150
260
Operating junction and storage temperature range
Soldering recommendations (peak temperature) d, e
TJ, Tstg
°C
THERMAL RESISTANCE RATINGS
PARAMETER
Maximum junction to ambient b
SYMBOL
RthJA
TYPICAL
24
MAXIMUM
UNIT
t 10 s
Steady state
33
°C/W
Maximum junction to case (drain)
RthJC
1.9
2.4
Notes
a. TC = 25 °C
b. Surface mounted on 1" x 1" FR4 board
c. t = 10 s
d. See solder profile (www.vishay.com/doc?73257). The PowerPAK 1212-8S is a leadless package. The end of the lead terminal is exposed
copper (not plated) as a result of the singulation process in manufacturing. A solder fillet at the exposed copper tip cannot be guaranteed
and is not required to ensure adequate bottom side solder interconnection
e. Rework conditions: manual soldering with a soldering iron is not recommended for leadless components
f. Maximum under steady state conditions is 81 °C/W
S23-0006-Rev. B, 16-Jan-2023
Document Number: 62167
1
For technical questions, contact: pmostechsupport@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000