0805 COMMONMODECHOKES
Common Mode Chokes for Critical Applications
•ꢀEliminates virtually all common mode noise in high-speed,
differential mode signal transmission applications such as
USB 2.0, IEEE1394, HDMI and LVDS.
•ꢀMost provide >25 dB common mode attenuation and
>100 ohms impedance.
Core material Ferrite
Terminations Gold over nickel over silver-palladium-glass frit. Other
terminations available at additional cost
Weight 14.9 – 15.2 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+105°C with derated current
Storage temperature Component: –55°C to +105°C.
Tape and reel packaging: –55°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Packaging 2000 per 7″reel; Plastic tape: 8 mm wide, 0.23 mm thick,
4 mm pocket spacing, 1.14 mm pocket depth
Common mode
Common mode
Inductance2 DCR max3 Isolation Irms4
impedance typ (Ohms)
attenuation typ (dB)
Part number1
10 MHz 100 MHz 500 MHz
10 MHz 100 MHz 500 MHz
min (nH)
(Ohms)
(Vrms) (mA)
CP336FRA421MAZ
CP336FRA901MAZ
CP336FRA172MAZ
CP336FRA262MAZ
CP336FRA372MAZ
14
28
57
85
118
42
90
170
260
370
70
154
303
435
641
1.1
1.4
2.3
3.0
4.5
2.3
4.2
6.7
8.6
11.9
8.4
16.9
22.0
27.8
34.3
23
47
84
147
189
0.12
0.17
0.25
0.26
0.32
250
250
250
250
250
500
500
500
500
500
CP336FRA502MAZ
CP336FRA672MAZ
CP336FRA902MAZ
148
246
294
500
670
900
945
1231
1715
4.9
8.4
8.7
14.5
16.6
18.7
31.3
30.0
30.5
273
322
413
0.37
0.45
0.65
250
250
250
500
500
250
0.090
2,29
1. When ordering, please specify termination and testing codes:
CP336FRA902MAZ
max
1
2
Termination: A = RoHS compliant gold over nickel over silver-
0.065
max
palladium-glass frit
1,65
Special order:
4
3
C= Tin-lead over gold over nickel over silver-palladium-
0.004
0,10
glass frit
0.040
1,02
0.020
0,51
0.030 0.036
0,76
F = Tin-silver-copper over gold over nickel over silver-
0,91
palladium-glass frit
0.014
0,36
Testing:
Z = COTS
H= Screening per Coilcraft CP-SA-10001
2
1
4
1
2
3
0.068
1,73
2. Inductance measured at 100 MHz using an Agilent/HP 4286A
impedance analyzer and a Coilcraft SMD-A fixture.
3. DCR is specified per winding.
4. Current per winding that causes a 20°C rise from 25°C ambient.
5. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
max
4
3
0.018
0,46
0.020
0,51
Recommended
Land Pattern
inches
mm
Dimensions are in
®
Document CP306-1 Revised 09/07/12
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Email cps@coilcraft.com Specifications subject to change without notice.
www.coilcraft-cps.com Please check our web site for latest information.
Fax 847-639-1508
1102 Silver Lake Road
Cary, IL 60013
Phone 800-981-0363
© Coilcraft, Inc. 2012