IS43R86400E
IS43/46R16320E, IS43/46R32160E
16Mx32, 32Mx16, 64Mx8
512Mb DDR SDRAM
JANUARY 2020
FEATURES
DEVICE OVERVIEW
• VDD and VDDQ: 2.5V 0.2V ꢀ(5ꢁ (-6
• VDD and VDDQ: 2.5V 0.1V ꢀ(ꢂ6
• SSTL_2 compatible I/O
• Double(data rate architecture; two data transfers
per clock cycle
• Bidirectionalꢁ data strobe ꢀDQS6 is transmitted/
received with dataꢁ to be used in capturing data
at the receiver
• DQS is edge(aligned with data for READs and
centre(aligned with data for WRITEs
ISSI’s 512(Mbit DDR SDRAM achieves high speed data
transfer using pipeline architecture and two data word
accesses per clock cycle. The 53-ꢁ870ꢁ912(bit memory
array is internally organized as four banks of 128Mb to
allow concurrent operations. The pipeline allows Read
and Write burst accesses to be virtually continuousꢁ with
the option to concatenate or truncate the bursts. The
programmable features of burst lengthꢁ burst sequence
and CAS latency enable further advantages. The device
is available in 8(bitꢁ 1-(bit and 32(bit data word size
Input data is registered on the I/O pins on both edges
of Data Strobe signalꢀs6ꢁ while output data is referenced
to both edges of Data Strobe and both edges of CLK.
Commands are registered on the positive edges of CLK.
• Differential clock inputs ꢀCK and CK6
• DLL aligns DQ and DQS transitions with CK
transitions
• Commands entered on each positive CK edge;
data and data mask referenced to both edges of
DQS
An Auto Refresh mode is providedꢁ along with a Self
Refresh mode. All I/Os are SSTL_2 compatible.
ADDRESS TABLE
• Four internal banks for concurrent operation
• Data Mask for write data. DM masks write data
at both rising and falling edges of data strobe
• Burst Length: 2ꢁ ꢂ and 8
Parameter
16M x 32
32M x 16
64M x 8
Configuration
ꢂM x 32 x ꢂ
banks
8M x 1- x ꢂ
banks
1-M x 8 x ꢂ
banks
• Burst Type: Sequential and Interleave mode
• Programmable CAS latency: 2ꢁ 2.5 and 3
• Auto Refresh and Self Refresh Modes
• Concurrent Auto Precharge Supported
• TRAS Lockout supported ꢀtRAP = tRCD6
Bank Address Pins
BA0ꢁ BA1
BA0ꢁ BA1
A10/AP
BA0ꢁ BA1
A10/AP
Autoprecharge Pins A8/AP
Row Address
8KꢀA0 – A126 8KꢀA0 – A126 8KꢀA0 – A126
Column Address
512ꢀA0 – A7ꢁ 1KꢀA0 – A96
A96
2KꢀA0 – A9ꢁ
A116
Refresh Count
Com./Ind./A1
A2
OPTIONS
8K / -ꢂms
8K / 1-ms
8K / -ꢂms
8K / 1-ms
8K / -ꢂms
8K / 1-ms
• Configurationꢀs6: 1-Mx32ꢁ 32Mx1-ꢁ -ꢂMx8
• Packageꢀs6:
1ꢂꢂ Ball BGA ꢀx326
--(pin TSOP(II ꢀx8ꢁ x1-6 and -0 Ball BGA ꢀx8ꢁ x1-6
• Lead(free package
KEY TIMING PARAMETERS
Speed Grade
-4
-5
-6
Units
x8, x16
• Temperature Range:
only
Commercial ꢀ0°C to +70°C6
Industrial ꢀ(ꢂ0°C to +85°C6
Automotiveꢁ A1 ꢀ(ꢂ0°C to +85°C6
Automotiveꢁ A2 ꢀ(ꢂ0°C to +105°C6
FCk Max CL = 3
FCk Max CL = 2.5
FCk Max CL = 2
250
1-7
133
200
1-7
133
1-7
1-7
133
MHz
MHz
MHz
Copyright © 2020 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without
notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest
version of this device specification before relying on any published information and before placing orders for products.
Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reason-
ably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications
unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that:
a.) the risk of injury or damage has been minimized;
b.) the user assume all such risks; and
c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances
Integrated Silicon Solution, Inc.
1
Rev. B
01/13/2020