Datasheet > TDA8002BT/5

TDA8002BT/5

更新时间： 2024-01-17 13:34:25

品牌	Logo	应用领域
恩智浦 - NXP		/
页数	文件大小	规格书
28页	131K
描述
IC card interface

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

TDA8002BT/5 数据手册

Philips Semiconductors

Product speciﬁcation

IC card interface

TDA8002

If wave soldering cannot be avoided, for LQFP

packages with a pitch (e) larger than 0.5 mm, the

following conditions must be observed:

SOLDERING

Introduction

There is no soldering method that is ideal for all IC

packages. Wave soldering is often preferred when

through-hole and surface mounted components are mixed

on one printed-circuit board. However, wave soldering is

not always suitable for surface mounted ICs, or for

printed-circuits with high population densities. In these

situations reflow soldering is often used.

• A double-wave (a turbulent wave with high upward

pressure followed by a smooth laminar wave)

soldering technique should be used.

• The footprint must be at an angle of 45° to the board

direction and must incorporate solder thieves

downstream and at the side corners.

This text gives a very brief insight to a complex technology.

A more in-depth account of soldering ICs can be found in

our “IC Package Databook” (order code 9398 652 90011).

Wave soldering techniques can be used for all SO

packages if the following conditions are observed:

• A double-wave (a turbulent wave with high upward

pressure followed by a smooth laminar wave) soldering

technique should be used.

Reﬂow soldering

Reflow soldering techniques are suitable for all LQFP and

SO packages.

• The longitudinal axis of the package footprint must be

Reflow soldering requires solder paste (a suspension of

fine solder particles, flux and binding agent) to be applied

to the printed-circuit board by screen printing, stencilling or

pressure-syringe dispensing before package placement.

parallel to the solder flow.

• The package footprint must incorporate solder thieves at

the downstream end.

METHOD (LQFP AND SO)

Several methods exist for reflowing; for example,

infrared/convection heating in a conveyor type oven.

Throughput times (preheating, soldering and cooling) vary

between 50 and 300 seconds depending on heating

method. Typical reflow peak temperatures range from

215 to 250 °C.

During placement and before soldering, the package must

be fixed with a droplet of adhesive. The adhesive can be

applied by screen printing, pin transfer or syringe

dispensing. The package can be soldered after the

adhesive is cured.

Maximum permissible solder temperature is 260 °C, and

maximum duration of package immersion in solder is

10 seconds, if cooled to less than 150 °C within

Wave soldering

LQFP

6 seconds. Typical dwell time is 4 seconds at 250 °C.

Wave soldering is not recommended for LQFP packages.

This is because of the likelihood of solder bridging due to

closely-spaced leads and the possibility of incomplete

solder penetration in multi-lead devices.

A mildly-activated flux will eliminate the need for removal

of corrosive residues in most applications.

Repairing soldered joints

CAUTION

Fix the component by first soldering two diagonally-

opposite end leads. Use only a low voltage soldering iron

(less than 24 V) applied to the flat part of the lead. Contact

time must be limited to 10 seconds at up to 300 °C. When

using a dedicated tool, all other leads can be soldered in

one operation within 2 to 5 seconds between

270 and 320 °C.

Wave soldering is NOT applicable for all LQFP

packages with a pitch (e) equal or less than 0.5 mm.

1997 Nov 04

1...20 21 222324 25 26...28

中文翻译

下载PDF

与TDA8002BT/5相关器件

型号	品牌	获取价格	描述	数据表
TDA8002BT/5/C1	NXP	获取价格	IC SPECIALTY MICROPROCESSOR CIRCUIT, PDSO28, Microprocessor IC:Other
TDA8002BT/5/C1-T	NXP	获取价格	IC SPECIALTY MICROPROCESSOR CIRCUIT, PDSO28, Microprocessor IC:Other
TDA8002BT/5/C2	NXP	获取价格	IC card interface
TDA8002BT/5/C2-T	NXP	获取价格	IC SPECIALTY MICROPROCESSOR CIRCUIT, PDSO28, Microprocessor IC:Other
TDA8002BT/5C1-T	NXP	获取价格	IC SPECIALTY MICROPROCESSOR CIRCUIT, PDSO28, Microprocessor IC:Other
TDA8002C	NXP	获取价格	IC card interface
TDA8002C/AD	NXP	获取价格	IC SPECIALTY MICROPROCESSOR CIRCUIT, PDSO28, 7.50 MM, PLASTIC, SO-28, Microprocessor IC:Ot
TDA8002C/AD-T	NXP	获取价格	IC SPECIALTY MICROPROCESSOR CIRCUIT, PDSO28, 7.50 MM, PLASTIC, SO-28, Microprocessor IC:Ot
TDA8002C/BD	NXP	获取价格	IC SPECIALTY MICROPROCESSOR CIRCUIT, PDSO28, 7.50 MM, PLASTIC, SO-28, Microprocessor IC:Ot
TDA8002C/CD	NXP	获取价格	IC SPECIALTY MICROPROCESSOR CIRCUIT, PDSO28, 7.50 MM, PLASTIC, SO-28, Microprocessor IC:Ot

与TDA8002BT/5相关文章

LM317T数据手册解读：产品特性、应用、封装与引脚详解
2024-06-14

14
一文带你了解?DB3二极管好坏判断、参数信息、替代推荐
2024-06-14

15
LM358DR数据手册：引脚说明、电气参数及替换型号推荐
2024-06-14

10
OP07CP数据手册解读：引脚信息、电子参数
2024-06-14

16

产品中心

服务支持

精选活动

关于我们

帮助中心

TDA8002BT/5

TDA8002BT/5 数据手册

与TDA8002BT/5相关器件

与TDA8002BT/5相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

TDA8002BT/5

TDA8002BT/5 数据手册

与TDA8002BT/5相关器件

与TDA8002BT/5相关文章

您还可以找

您在本页遇到什么问题？