LM5158-Q1, LM51581-Q1
SNVSB88A – AUGUST 2021 – REVISED OCTOBER 2021
LM5158x-Q1 2.2-MHz Wide VIN 85-V Output Boost/SEPIC/Flyback Converter with Dual
Random Spread Spectrum
1 Features
2 Applications
•
AEC-Q100 qualified for automotive applications
– Temperature grade 1: –40°C to +125°C TA
Functional Safety-Capable
– Documentation available to aid functional safety
system design
Suited for wide operating range for car battery
applications
– 3.2-V to 60-V input operating range (65-V abs
max)
•
Battery-powered wide input boost, SEPIC, flyback
converter
Automotive voltage stabilizer in SEPIC
High voltage LiDAR power supply
Automotive LED bias supply
Multiple-output flyback without optocoupler
Hold-up capacitor charger
Inverter bias supply
•
•
•
•
•
•
•
•
•
Piezo driver/motor driver bias supply
– 83-V maximum output (85-V abs max)
– Minimum boost supply voltage of 1.5 V when
BIAS ≥ 3.2 V
– Input transient protection up to 65 V
– Minimized battery drain
3 Description
The LM5158x-Q1 device is a wide input range, non-
synchronous boost converter with an integrated 85-V,
3.26-A (LM5158-Q1) or 85-V, 1.63-A (LM51581-Q1)
power switch.
•
•
Low shutdown current (IQ ≤ 2.6 µA)
Low operating current (IQ ≤ 670 µA)
The device can be used in boost, SEPIC, and flyback
topologies. It can start up from a single-cell battery
with a minimum of 3.2 V. It can operate with the input
supply voltage as low as 1.5 V if the BIAS pin is
greater than 3.2 V.
•
Small solution size and low cost
– Maximum switching frequency up to 2.2 MHz
– 16-pin QFN package (3 mm × 3 mm) with
wettable flanks
– Integrated error amplifier allows primary-side
regulation without optocoupler (flyback)
– Minimized undershoot during cranking
– Accurate current limit (see the Device
Comparison Table)
EMI mitigation
– Selectable dual random spread spectrum
– Lead-less package
The BIAS pin operates up to 60 V (65-V absolute
maximum) for automotive load dump. The switching
frequency is dynamically programmable from 100
kHz to 2.2 MHz with an external resistor. Switching
at 2.2 MHz minimizes AM band interference and
allows for a small solution size and fast transient
response. The device provides a selectable Dual
Random Spread Spectrum to help reduce the EMI
over a wide frequency range.
•
•
•
Higher efficiency with low-power dissipation
– 133-mΩ RDSON switch
Device Information
– Fast switching, small switching loss
Avoid AM band interference and crosstalk
– Optional clock synchronization
– Dynamically programmable wide switching
frequency from 100 kHz to 2.2 MHz
Integrated protection features
PART NUMBER
LM5158-Q1
PACKAGE(1)
BODY SIZE (NOM)
WQFN (16)
3.00 mm × 3.00 mm
LM51581-Q1
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
•
– Constant current limiting over input voltage
– Selectable hiccup mode overload protection
– Programmable line UVLO
VLOAD
VSUPPLY
BIAS VCC
SW
– OVP protection
– Thermal shutdown
Accurate ±1% accuracy feedback reference
Adjustable soft start
UVLO
RT
FB
COMP
•
•
•
•
SS
PGOOD
PGND AGND MODE
PGOOD indicator
Create a custom design using the LM5158x-Q1
with the WEBENCH® Power Designer
Typical SEPIC Application
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.