50 mA/500 mA, Ultralow Power Step-Down
Regulator with Battery Voltage Monitor
Data Sheet
ADP5302
FEATURES
TYPICAL APPLICATION CIRCUIT
Input supply voltage range: 2.15 V to 6.50 V
Operates down to 2.00 V
V
=
IN
2.2µH
V
2.15V TO 6.50V
OUT
PVIN
EN
SW
10µF
Ultralow 240 nA quiescent current with no load
Selectable output voltages of 1.2 V to 3.6 V, or 0.8 V to 5.0 V
1.5ꢀ output accuracy over the full temperature range in
pulse-width modulation (PWM) mode
Selectable hysteresis mode or PWM operation mode
Output current
Up to 50 mA in hysteresis mode
Up to 500 mA in PWM mode
VINOK flag to monitor input battery voltage
Ultrafast stop switching control
100ꢀ duty cycle operation mode
ADP5302
10µF
(LFCSP-10)
ON
PGND
FB
OFF
PWM
HYS
SYNC/
MODE
STOP
SW
STOP
AGND
VINOK
VID
VID0: 1.2V VID8: 2.5V
VID1: 1.5V VID9: 2.6V
VID2: 1.8V VID10: 2.7V
VID3: 2.0V VID11: 2.8V
VID4: 2.1V VID12: 2.9V
VID5: 2.2V VID13: 3.0V
VID6: 2.3V VID14: 3.3V
VID7: 2.4V VID15: 3.6V
R0
EPAD
2 MHz switching frequency with optional synchronization
input from 1.5 MHz to 2.5 MHz
Figure 1.
Quick output discharge (QOD) option
UVLO, OCP, and TSD protection
10-lead, 3 mm × 3 mm LFCSP package
Junction temperature: −40°C to +125°C
APPLICATIONS
Energy (gas, water) metering
Portable and battery-powered equipment
Medical applications
Keep-alive power supplies
GENERAL DESCRIPTION
The ADP5302 is a high efficiency, ultralow quiescent current
step-down regulator that draws only 240 nA quiescent current
to regulate the output at no load.
The ADP5302 integrates an ultralow power comparator with a
factory programmable voltage reference to monitor the input
battery voltage. The regulator runs at a 2 MHz switching
frequency in PWM mode, and the SYNC/MODE pin can be
synchronized to an external clock from 1.5 MHz to 2.5 MHz.
The ADP5302 runs from an input voltage of 2.15 V to 6.50 V,
allowing the use of multiple alkaline or NiMH cells, Li-Ion cells,
or other power sources. The output voltage is selectable from 0.8 V
to 5.0 V by an external, dynamic voltage identification (VID)
resistor and a factory fuse. The total solution requires only four
tiny external components.
The ADP5302 includes an extra STOP pin that can temporarily
disable the regulator switching; in this way, a quiet system environ-
ment can be achieved to benefit the noise sensitive circuitry, which
includes data conversion, RF data transmission, and analog sensors.
The ADP5302 can operate between hysteresis mode and PWM
mode via the SYNC/MODE pin. In hysteresis mode, the regulator
achieves excellent efficiency at less than 1 mW and provides up to
50 mA of output current. In PWM mode, the regulator produces a
lower output ripple and supplies up to 500 mA of output current.
The flexible configuration capability during operation of the
device enables very efficient power management to meet both
long battery life and low system noise requirements.
Other key features in the ADP5302 include separate enabling,
QOD, and safety features, such as overcurrent protection
(OCP), thermal shutdown (TSD), and input undervoltage
lockout (UVLO).
The ADP5302 is available in a 10-lead, 3 mm × 3 mm LFCSP
package rated for the −40°C to +125°C junction temperature range.
Rev. B
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2015–2019 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com