W144
nation of assigned device functions. A short time after
power-up, the logic state of each pin is latched and the pins
become clock outputs. This feature reduces device pin count
by combining clock outputs with input select pins.
Key Specifications
CPU Cycle-to-Cycle Jitter: ..........................................250 ps
CPU to CPU Output Skew: .........................................175 ps
PCI to PCI Output Skew: .............................................500 ps
An external 10-k: “strapping” resistor is connected between
the l/O pin and ground or VDD. Connection to ground sets a
latch to “0,” connection to VDD sets a latch to “1.” Figure 1 and
Figure 2 show two suggested methods for strapping resistor
connections.
V
DDQ3: .....................................................................3.3V 5ꢀ
DDQ2: .....................................................................2.5V 5ꢀ
V
SDRAMIN to SDRAM0:11 Delay: ..........................3.7 ns typ.
SDRAM0:11 (leads) to SDRAM_F Skew:..............0.4 ns typ.
Table 2. Mode Input Table
Upon W144 power up, the first 2 ms of operation is used for
input logic selection. During this period, the five I/O pins (7, 8,
25, 26, 46) are three-stated, allowing the output strapping
resistor on the l/O pins to pull the pin and their associated
capacitive clock load to either a logic HIGH or LOW state. At
the end of the 2ms period, the established logic “0” or “1”
condition of the l/O pin is latched. Next the output buffer is
enabled converting the l/O pins into operating clock outputs.
The 2-ms timer starts when VDD reaches 2.0V. The input bits
can only be reset by turning VDD off and then back on again.
Mode
Pin2
0
1
PCI_STOP#
REF0
Overview
It should be noted that the strapping resistors have no signif-
icant effect on clock output signal integrity. The drive
impedance of clock outputs are <40: (nominal) which is
minimally affected by the 10-k: strap to ground or VDD. As
with the series termination resistor, the output strapping
resistor should be placed as close to the l/O pin as possible in
order to keep the interconnecting trace short. The trace from
the resistor to ground or VDD should be kept less than two
inches in length to prevent system noise coupling during input
logic sampling.
The W144 was developed as a single-chip device to meet the
clocking needs of the Intel 440BX AGPset. In addition to the
typical outputs provided by standard 100-MHz 440BX FTGs,
the W144 adds a thirteen output buffer, supporting SDRAM
DIMM modules in conjunction with the chipset.
Cypress’s proprietary spread spectrum frequency synthesis
technique is a feature of the CPU and PCI outputs. When
enabled, this feature reduces the peak EMI measurements of
not only the output signals and their harmonics, but also of any
other clock signals that are properly synchronized to them.
When the clock outputs are enabled following the 2-ms input
period, the specified output frequency is delivered on the pin,
assuming that VDD has stabilized. If VDD has not yet reached
full value, output frequency initially may be below target but will
increase to target once VDD voltage has stabilized. In either
case, a short output clock cycle may be produced from the
CPU clock outputs when the outputs are enabled.
Functional Description
I/O Pin Operation
Pins 7, 8, 25, 26, and 46 are dual-purpose l/O pins. Upon
power-up these pins act as logic inputs, allowing the determi-
V
DD
Output Strapping Resistor
Series Termination Resistor
10 k
(Load Option 1)
:
Clock Load
W144
Output
Buffer
Power-on
Reset
Timer
Hold
Output
Low
Output Three-state
10 k:
(Load Option 0)
Q
D
Data
Latch
Figure 1. Input Logic Selection Through Resistor Load Option
Rev 1.0,November 21, 2006
Page 3 of 13
5秒后页面跳转
资料手册解读：UC3842参数和管脚说明
一文带你了解无源晶振的负载电容为何要加两颗谐振电容CL1和CL2
玻璃管保险丝与陶瓷管保险丝：区别与替代性探讨
PCF8574资料解读：主要参数分析、引脚说明
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
