CY7C138AV/144AV/006AV
CY7C139AV/145AV/016AV
CY7C007AV/017AV
Pin Definitions
Left Port
CEL
Right Port
Description
CER
Chip Enable
R/WL
OEL
R/WR
OER
Read/Write Enable
Output Enable
A0L–A14L
I/O0L–I/O8L
SEML
INTL
A0R–A14R
Address (A0–A11 for 4K devices; A0–A12 for 8K devices; A0–A13 for 16K devices; A0–A14 for 32K)
I/O0R–I/O8R Data Bus Input/Output (I/O0–I/O7 for x8 devices and I/O0–I/O8 for x9)
SEMR
INTR
Semaphore Enable
Interrupt Flag
Busy Flag
BUSYL
M/S
BUSYR
Master or Slave Select
Power
VCC
GND
Ground
NC
No Connect
or token, from one port to the other to indicate that a shared
resource is in use. The semaphore logic is comprised of eight
shared latches. Only one side can control the latch
(semaphore) at any time. Control of a semaphore indicates
that a shared resource is in use. An automatic power-down
feature is controlled independently on each port by a Chip
Select (CE) pin.
Architecture
The CY7C138AV/144AV/006AV/007AV and CY7C139AV/
145AV/016AV/017AV consist of an array of 4K, 8K, 16K, and
32K words of 8 and 9 bits each of dual-port RAM cells, I/O and
address lines, and control signals (CE, OE, R/W). These
control pins permit independent access for reads or writes to
any location in memory. To handle simultaneous writes/reads
to the same location, a BUSY pin is provided on each port. Two
interrupt (INT) pins can be utilized for port-to-port communi-
cation. Two semaphore (SEM) control pins are used for
allocating shared resources. With the M/S pin, the device can
function as a master (BUSY pins are outputs) or as a slave
(BUSY pins are inputs). The device also has an automatic
power-down feature controlled by CE. Each port is provided
with its own output enable control (OE), which allows data to
be read from the device.
Read and Write Operations
When writing data must be set up for a duration of tSD before
the rising edge of R/W in order to guarantee a valid write. A
write operation is controlled by either the R/W pin (see Write
Cycle No. 1 waveform) or the CE pin (see Write Cycle No. 2
waveform). Required inputs for non-contention operations are
summarized in Table 1.
If a location is being written to by one port and the opposite
port attempts to read that location, a port-to-port flowthrough
delay must occur before the data is read on the output;
otherwise the data read is not deterministic. Data will be valid
on the port tDDD after the data is presented on the other port.
Functional Description
The CY7C138AV/144AV/006AV/007AV and CY7C139AV/
145AV/ 016AV/017AV are low-power CMOS 4K, 8K, 16K, and
32K x8/9 dual-port static RAMs. Various arbitration schemes
are included on the devices to handle situations when multiple
processors access the same piece of data. Two ports are
provided, permitting independent, asynchronous access for
reads and writes to any location in memory. The devices can
be utilized as standalone 8/9-bit dual-port static RAMs or
multiple devices can be combined in order to function as a
16/18-bit or wider master/slave dual-port static RAM. An M/S
pin is provided for implementing 16/18-bit or wider memory
applications without the need for separate master and slave
devices or additional discrete logic. Application areas include
interprocessor/multiprocessor designs, communications
status buffering, and dual-port video/graphics memory.
When reading the device, the user must assert both the OE
and CE pins. Data will be available tACE after CE or tDOE after
OE is asserted. If the user wishes to access a semaphore flag,
then the SEM pin must be asserted instead of the CE pin and
OE must also be asserted.
Interrupts
The upper two memory locations may be used for message
passing. The highest memory location (FFF for the
CY7C138AV/9AV, 1FFF for the CY7C144AV/5AV, 3FFF for the
CY7C006AV/16AV, 7FFF for the CY7C007AV/17AV) is the
mailbox for the right port and the second-highest memory
location (FFE for the CY7C138AV/9AV, 1FFE for the
CY7C144AV/5AV, 3FFE for the CY7C006AV/16AV, 7FFE for
the CY7C007AV/17AV) is the mailbox for the left port. When
one port writes to the other port’s mailbox, an interrupt is
generated to the owner. The interrupt is reset when the owner
reads the contents of the mailbox. The message is user
defined.
Each port has independent control pins: Chip Enable (CE),
Read or Write Enable (R/W), and Output Enable (OE). Two
flags are provided on each port (BUSY and INT). BUSY
signals that the port is trying to access the same location
currently being accessed by the other port. The Interrupt flag
(INT) permits communication between ports or systems by
means of a mail box. The semaphores are used to pass a flag,
Each port can read the other port’s mailbox without resetting
the interrupt. The active state of the busy signal (to a port)
Document #: 38-06051 Rev. *C
Page 5 of 20
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
