50 mA/500 mA, High Efficiency,
Ultralow Power Step-Down Regulator
Data Sheet
ADP5301
FEATURES
TYPICAL APPLICATION CIRCUIT
Input start-up voltage range: 2.15 V to 6.50 V
Operates down to 2.00 V voltage
Ultralow 180 nA quiescent current with no load
Selectable output voltage of 1.2 V to 3.6 V or 0.8 V to 5.0 V
1.5ꢀ output accuracy over full temperature range in
PWM mode
2.2µH
V
= 3.6V
10µF
V
OUT
IN
PVIN
EN
SW
ADP5301
10µF
(9-BALL WLCSP)
ON
PGND
OFF
HYS
PWM
SYNC/
MODE
Selectable hysteresis mode or PWM operation mode
Output current
FB
VID0: 1.2V VID8: 2.5V
VID1: 1.5V VID9: 2.6V
VID2: 1.8V VID10: 2.7V
VID3: 2.0V VID11: 2.8V
VID4: 2.1V VID12: 2.9V
VID5: 2.2V VID13: 3.0V
VID6: 2.3V VID14: 3.3V
VID7: 2.4V VID15: 3.6V
Up to 50 mA in hysteresis mode
Up to 500 mA in PWM mode
VOUTOK flag monitors the output voltage
100ꢀ duty cycle operation mode
2 MHz switching frequency with optional synchronization
input from 1.5 MHz to 2.5 MHz
VOUTOK
VID
R
VID
AGND
Figure 1.
QOD option
UVLO, OCP, and TSD protection
9-ball, 1.65 mm × 1.87 mm WLCSP
−40°C to +125°C junction temperature
APPLICATIONS
Energy (gas and water) metering
Portable and battery-powered equipment
Medical applications
Keep-alive power supplies
GENERAL DESCRIPTION
The ADP5301 is a high efficiency, ultralow quiescent current
step-down regulator that draws only a 180 nA quiescent
current to regulate the output at no load.
The ADP5301 contains a VOUTOK flag, which monitors the
output voltage and runs at a 2 MHz switching frequency in
PWM mode. SYNC/MODE can synchronize to an external
clock from 1.5 MHz to 2.5 MHz.
The ADP5301 runs from an input startup voltage range of 2.15 V
to 6.50 V, allowing the use of multiple alkaline/NiMH, Li-Ion
cells, or other power sources. The output voltage is selectable from
0.8 V to 5.0 V by an external VID resistor and factory fuse. The
total solution requires only four tiny external components.
Other key features in the ADP5301 include separate enabling,
quick output discharge (QOD), and safety features such as
overcurrent protection (OCP), thermal shutdown (TSD), and
input undervoltage lockout (UVLO).
The ADP5301 can operate between hysteresis mode and PWM
mode via the SYNC/MODE pin. The regulator in hysteresis mode
achieves excellent efficiency at a power of less than 1 mW and
provides up to 50 mA of output current. The regulator in PWM
mode produces a lower output ripple and supplies up to 500 mA
of output current. The flexible configuration capability during
operation of the device enables very efficient power management
to meet both the longest battery life and low system noise
requirements.
The ADP5301 is available in a 9-ball, 1.65 mm × 1.87 mm
WLCSP rated for a −40°C to +125°C junction temperature range.
Rev. C
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2015–2019 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com