TPD4S214
www.ti.com
SLVSBR1A –JANUARY 2013–REVISED FEBRUARY 2013
USB OTG Companion Device with V Over Voltage, Over Current Protection, and Four
BUS
Channel ESD Clamps
Check for Samples: TPD4S214
1
FEATURES
•
•
ESD Performance D+, D-, ID, VBUS PINS
–
–
±15-kV Contact Discharge (IEC 61000-4-2)
±15-kV Air Gap Discharge (IEC 61000-4-2)
•
Input Voltage Protection at VBUS from –7 V to
30 V
•
Low RDS(ON) N-CH FET Switch for High
Efficiency
Space Saving WCSP (12-YFF) Package
APPLICATIONS
•
•
Compliant with USB2.0 and USB3.0 OTG spec
User Adjustable Current Limit From 250 mA to
Beyond 1.2 A
•
•
•
•
•
Cell Phones
Tablet, eBook
•
•
•
•
•
Built-in Soft-start
Set-Top Box
Reverse Current Blocking
Over Voltage Lock Out for VBUS
Under Voltage Lock Out for VOTG_IN
Portable Media Players
Digital Camera
Thermal Shutdown and Short Circuit
Protection
YFF PACKAGE
(TOP SIDE/SEE-THROUGH VIEW)
1.4-mm
•
Auto Retry on any Fault; no Latching off
States
12-YFF Pin Proposal
1
2
3
•
•
Integrated VBUS Detection Circuit
A
B
C
D
VOTG_IN
DET
VBUS
Low Capacitance TVS ESD Clamp for USB2.0
High Speed Data Rate
VOTG_IN
EN
FLT\
GND
D-
VBUS
ID
•
Internal 16ms Startup Delay
ADJ
D+
DESCRIPTION
The TPD4S214 is a single-chip protection solution for USB On-the-Go and other current limited USB
applications. This device includes an integrated low (RDS(ON) N-channel current limited switch for OTG current
supply to peripheral devices. TPD4S214 offers low capacitance TVS ESD clamps for the D+, D-, ID pins for both
USB2.0 and USB3.0 applications. The VBUS pin can handle continuous voltage ranging from –7 V to 30 V. The
over voltage lock-out (OVLO) at the VBUS pin ensures that if there is a fault condition at the VBUS line, the
TPD4S214 is able to isolate it and protects the internal circuitry from damage. Similarly, the under voltage lock
out (UVLO) at the VOTG_IN pin ensures that there is no power drain from the internal OTG supply to external VBUS
if VOTG_IN droops below safe operating level.
When EN is high, the OTG switch is activated and the FLT pin indicates whether there is a fault condition. The
soft start feature waits 16 ms to turn on the OTG switch after all operating conditions are met. The FLT pin
asserts low during any one of the following fault conditions: OVLO (VBUS > VOVLO), UVLO condition (VOTG_IN
<
VUVLO) over temperature, over current, short circuit condition, or reverse-current-condition (VBUS > VOTG_IN). The
OTG switch is turned off during any fault condition. Once the switch is turned off, the IC periodically rechecks the
faults internally. If the IC returns to normal operating conditions, the switch turns back on and FLT is reset to
high.
There is also a VBUS detection feature for facilitating USB communication between USB host and peripheral
device. See Table 2 for detection scheme. If this is not used, DET pin can be either floating or connected to
ground.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCT PREVIEW information concerns products in the
Copyright © 2013, Texas Instruments Incorporated
formative or design phase of development. Characteristic data and
other specifications are design goals. Texas Instruments reserves
the right to change or discontinue these products without notice.