600W Single Output Battery Charger
PB-600 series
Features :
2/3/8 stage charging (Note 4)
Universal AC input / Full range
Built-in active PFC function PF>0.95
Protection: Reverse polarity / Short circuit / Over voltage / Over temperature
Charger for lead-acid batteries
3 color LED loading indicator
Built-in remote ON-OFF control
Built-in temperature compensation function
Built-in fan speed control (depends on charging current)
3 years warranty
..
SPECIFICATION
MODEL
PB-600-12
PB-600-24
PB-600-48
BOOST CHARGE VOLTAGE 14.4V
28.8V
27.6V
57.6V
55.2V
FLOAT CHARGE VOLTAGE 13.8V
RECOMMENDED BATTERY
OUTPUT
135 ~ 400AH
70 ~ 210AH
35 ~ 105AH
CAPACITY(AMP HOURS)(Note 3)
BATTERY TYPE
Open & Sealed Lead Acid
40A
OUTPUT CURRENT
21A
10.5A
VOLTAGE RANGE
90 ~ 264VAC
47 ~ 63Hz
127 ~ 370VDC
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
0.95/230VAC
86%
0.98/115VAC at full load
87%
89%
INPUT
6.8A/115VAC
25A/115VAC
<3.5mA / 240VAC
16 ~ 18V
3.4A/230VAC
50A/230VAC
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
32 ~ 35V
64.5 ~ 69.5V
OVER VOLTAGE
Protection type : Shut down o/p voltage, re-power on to recover
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
PROTECTION
OVER TEMPERATURE
REMOTE CONTROL
LEAKAGE CURRENT FROM BATTERY (Typ.)
FAST CHARGE
Open: Normal work
1mA
Short: Stop Charging
2 / 3 / 8 stage selectable
Relay contact (RY15)
Relay contact (RY13)
By NTC
FUNCTION
CHARGING OK
OUTPUT OK
TEMPERATURE SENSE
WORKING TEMP.
-20 ~ +60 (Refer to "Derating Curve")
20 ~ 90% RH non-condensing
-40 ~ +85 , 10 ~ 95% RH
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
ENVIRONMENT
0.05%/ (0 ~ 50
)
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
UL1012, TUV EN60335-1, EN60335-2-29 (except for 48V), EN60950-1(48V only) approved
I/P-O/P:3KVAC I/P-FG:1.8KVAC O/P-FG:0.5KVAC
SAFETY STANDARDS
WITHSTAND VOLTAGE
SAFETY &
ISOLATION RESISTANCE
EMC EMISSION
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH
Compliance to EN55022 (CISPR22), EN61000-3-2,-3
EMC
(Note 2)
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024; light industry level, criteria A
135.6Khrs min. MIL-HDBK-217F (25
230*158*67mm(L*W*H)
)
MTBF
OTHERS
NOTE
DIMENSION
PACKING
2.2Kg; 6pcs/14.2Kg/1.76CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
3. This is Mean Well's suggested range. Please consult your battery manufacturer for their suggestions about maximum charging current limitation.
4. Please choose the "3 stage" selection when the charger is used to charge the batteries and power the loads in the same time.
File Name:PB-600-SPEC 2011-08-18