MN101E35 Series
Type
MN101E35A
MN101E35D
MN101EF35A
32K
MN101EF35D
FLASH
MN101EF35G
Internal ROM type
ROM (byte)
RAM (byte)
Mask ROM
32K
68K
64K+4K
128K+4K
8K
4K
HQFP048-P-0707B,
TQFP048-P-0707B
Package (Lead-free)
TQFP048-P-0707B
HQFP048-P-0707B
0.042 µs (at 2.2 V to 3.6 V, 24 MHz, When USB unused)
0.0625 µs (at 3.0 V to 3.6 V, 16 MHz, When USB used)
62.5 µs (at 2.2 V to 3.6 V, 32 kHz)
Minimum Instruction
Execution Time
Interrupts
RESET. Watchdog. External 0 to 4. External 5 (key interrupt dedicated). External 6. Timer 0 to 4. Timer 6. Timer 7 (2 systems). Timer 8
(2 systems). Timer 9 (2 systems). Time base. Serial 1 (2 systems). Serial 2 (2 systems). Serial 4 (2 systems). A/D conversion finish. USB
interrupts
Timer Counter
8-bit timer × 6
Timer 0 ..................Square-wave output. PWM output. Event count. Simple pulse width measurement. Square-wave/PWM output to
large current terminal P03 (TM0IOB) possible
Timer 1 ..................Square-wave output. Event count
Timer 2 ..................Square-wave output. PWM output. Event count. Simple pulse width measurement. Square-wave/PWM output to
large current terminal P03 (TM2IOB) possible
Timer 3 ..................Square-wave output. Event count
Timer 4 ..................Square-wave output. PWM output. Event count. Simple pulse width measurement. Square-wave/PWM output to
large current terminal P02 (TM4IOC) possible
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 0, 1, 2 can be cascade-connected
Timer 0, 1, 2, 3 can be cascade-connected
16-bit timer × 3
Timer 7 ..................Square-wave output. PWM output (cycle/duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P00 (TM7IOB) possible
Timer 8 ..................Square-wave output. PWM output (cycle/duty continuous variable). Event count. Pulse width measurement. Input
capture. Square-wave/PWM output to large current terminal P01 (TM8IOB) possible
Timer 9 ..................Square-wave output. PWM output (cycle/duty continuous variable). Event count. Pulse width measurement. Input
capture
Time base timer: One-minute count setting
Watchdog timer × 1
Serial interface
Synchronous type/UART (full-duplex) × 2: Serial 1, 2
Synchronous type/Multi-master I2C × 1: Serial 4
Serial 4...................7-bit/10-bit address setting. General call
USB Functions
Conforms to USB 2.0: Full-speed (12 Mbps) supported
USB transceiver built-in. 3 end points (FIFO built-in independently)
FIFO size: EP0 = 16 bytes. EP1 = 128 bytes. EP2 = 128 bytes
EP0: Control transfer. IN/OUT (two ways)
EP1 to EP2: Interrupt/Bulk/Isochronous transfer supported. Settable to IN or OUT. Double Buffering function supported
When the MAXP size is set to a half or less of the MAXFIFO size for each EP, the Double Buffering function is made valid
automatically
I/O Pins
I/O
37 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
A/D converter
10-bit × 8 channels (with S/H)
MAD00061HEM