5秒后页面跳转
KMA210 PDF预览

KMA210

更新时间: 2024-10-28 12:04:59
品牌 Logo 应用领域
恩智浦 - NXP 传感器换能器磁场传感器
页数 文件大小 规格书
37页 591K
描述
Programmable angle sensor

KMA210 技术参数

是否Rohs认证:符合生命周期:End Of Life
Reach Compliance Code:unknown风险等级:5.73
Is Samacsys:N主体宽度:1.55 mm
主体长度或直径:5.35 mm外壳:PLASTIC
JESD-609代码:e3安装特点:THROUGH HOLE MOUNT
最大工作电流:10.5 mA最高工作温度:160 °C
最低工作温度:-40 °C输出接口类型:1-WIRE INTERFACE
输出范围:0.25-4.75V输出类型:ANALOG VOLTAGE
封装形状/形式:RECTANGULAR传感器/换能器类型:MAGNETIC FIELD SENSOR,MAGNETORESISTIVE
最大供电电压:5.5 V最小供电电压:4.5 V
表面贴装:NO端子面层:Tin (Sn)
端接类型:SOLDERBase Number Matches:1

KMA210 数据手册

 浏览型号KMA210的Datasheet PDF文件第2页浏览型号KMA210的Datasheet PDF文件第3页浏览型号KMA210的Datasheet PDF文件第4页浏览型号KMA210的Datasheet PDF文件第6页浏览型号KMA210的Datasheet PDF文件第7页浏览型号KMA210的Datasheet PDF文件第8页 
KMA210  
NXP Semiconductors  
Programmable angle sensor  
α
H
ext  
001aan665  
Fig 2. Angular measurement directions  
Since the Anisotropic MR (AMR) effect is periodic over 180, the sensor output is also  
180-periodic, where the angle is calculated relative to a freely programmable zero angle.  
The dashed line indicates the mechanical zero degree position.  
6. Analog output  
The KMA210 provides one analog output signal on pin OUT/DATA. The measured angle  
is converted linearly into a value, which is ratiometric to the supply voltage VDD. Either a  
positive or a negative slope is provided for this purpose.  
Table 3 describes the analog output behavior for a positive slope. If for example,  
a magnetic field angle, above the programmed maximum angle max, but below the clamp  
switch angle sw(CL) is applied to the sensor, then analog output is set to the upper  
clamping voltage. If the magnetic field angle is larger than the clamp switch angle, the  
analog output switches from upper to lower clamping voltage. In the case of a negative  
slope, the clamping voltages are changed.  
Table 3.  
Analog output behavior for a positive slope  
Magnetic field angle  
Analog output  
V(CL)u  
max < < sw(CL)  
sw(CL) < < ref + 180  
V(CL)l  
The analog output voltage range encodes both angular and diagnostic information. A valid  
angle value is between the upper and lower clamping voltage. If the analog output is in the  
diagnostic range, that is below 4 %VDD or above 96 %VDD, an error condition has been  
detected. The analog output repeats every 180.  
KMA210  
All information provided in this document is subject to legal disclaimers.  
© NXP B.V. 2011. All rights reserved.  
Product data sheet  
Rev. 2 — 7 December 2011  
5 of 37  

与KMA210相关器件

型号 品牌 获取价格 描述 数据表
KMA210:115 NXP

获取价格

KMA210 - Programmable angle sensor SIP 6-Pin
KMA210-115 NXP

获取价格

Programmable angle sensor
KMA215 NXP

获取价格

Programmable angle sensor with SAE J2716 SENT
KMA220 NXP

获取价格

Dual channel programmable angle sensor
KMA221 NXP

获取价格

Programmable angle sensor
KMA2D0DP20X KEC

获取价格

TSOP-6 PACKAGE
KMA2D3P20S KEC

获取价格

P-Ch Trench MOSFET
KMA2D4P20S KEC

获取价格

P-Ch Trench MOSFET
KMA2D4P20SA KEC

获取价格

SOT-23 PACKAGE
KMA2D7DP20X KEC

获取价格

TSOP-6 PACKAGE