CD4049UBT
Data Sheet
July 1999
File Number 4622.1
CMOS Hex Buffer/Converter
Features
Intersil’s Satellite Applications FlowTM (SAF) devices are fully
tested and guaranteed to 100kRAD total dose. These QML
Class T devices are processed to a standard flow intended
to meet the cost and shorter lead-time needs of large
volume satellite manufacturers, while maintaining a high
level of reliability.
• QML Class T, Per MIL-PRF-38535
• Radiation Performance
5
- Gamma Dose (γ) 1 x 10 RAD(Si)
2
- SEP Effective LET >75 MEV-gm/cm
• Inverting Type
The CD4049UBT is an Inverting Hex Buffer and features
• High Sink Current for Driving 2 TTL Loads
• High-to-Low Level Logic Conversion
• 100% Tested for Quiescent Current at 20V
• 5V, 10V and 15V Parametric Ratings
logic level conversion using only one supply (voltage (V ).
CC
The input signal high level (V ) can exceed the V
IH
supply
CC
voltage when this device is used for logic level conversions.
This device is intended for use as CMOS to DTL/TTL
converters and can drive directly two DTL/TTL loads. (V
=
CC
5V, V ≤ 0.4V, and I ≥ 3.3mA.
OL OL
Pinouts
The CD4049UBT is the designated replacement for the
CD4049BT (SBDIP), CDIP2-T16
TOP VIEW
CD4009UB. Because the CD4049UBT requires only one
power supply, it is preferred over the CD4009UB and
CD4010B and should be used in place of the CD4009UB in
all inverter, current driver, or logic level conversion
applications. In these applications the CD4049UBT is pin
compatible with the CD4009UB, and can be substituted for
this device in existing as well as in new designs. Terminal
No. 16 is not connected internally on the CD4049UBT,
therefore, connection to this terminal is of no consequence
to circuit operation. For applications not requiring high sink
current or voltage conversion, the CD4069UB Hex Inverter is
recommended.
V
1
2
3
4
5
6
7
8
16 NC
CC
G = A
A
15 L = F
14
F
H = B
B
13 NC
12 K = E
I = C
C
11
E
10 J = D
9
D
V
SS
Specifications
Specifications for Rad Hard QML devices are controlled by
the Defense Supply Center in Columbus (DSCC). The SMD
numbers listed below must be used when ordering.
CD4049BT (FLATPACK), CDFP4-F16
TOP VIEW
V
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
NC
L = F
F
CC
Detailed Electrical Specifications for the CD4049UBT are
contained in SMD 5962-96636. A “hot-link” is provided from
our website for downloading.
G = A
A
H = B
B
NC
K = E
E
www.intersil.com/spacedefense/newsafclasst.asp
Intersil’s Quality Management Plan (QM Plan), listing all
Class T screening operations, is also available on our web-
site.
I = C
C
J = D
D
V
SS
www.intersil.com/quality/manuals.asp
Ordering Information
TEMP.
ORDERING
NUMBER
PART
NUMBER
RANGE
( C)
o
5962R9663601TEC
5962R9663601TXC
CD4049UBDTR
CD4049UBKTR
-55 to 125
-55 to 125
NOTE: Minimum order quantity for -T is 150 units through
distribution, or 450 units direct.
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
1
Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation.