5秒后页面跳转
AD8324ACP-REEL7 PDF预览

AD8324ACP-REEL7

更新时间: 2024-01-14 07:35:10
品牌 Logo 应用领域
亚德诺 - ADI 线路驱动器或接收器驱动程序和接口接口集成电路
页数 文件大小 规格书
16页 639K
描述
3.3 V Upstream Cable Line Driver

AD8324ACP-REEL7 技术参数

是否无铅: 含铅是否Rohs认证: 不符合
生命周期:Active零件包装代码:QFN
包装说明:4 X 4 MM, MO-220VGGD-1, CSP-20针数:20
Reach Compliance Code:unknown风险等级:5.63
差分输出:YES驱动器位数:1
输入特性:STANDARD接口集成电路类型:LINE DRIVER
接口标准:GENERAL PURPOSEJESD-30 代码:S-XQCC-N20
JESD-609代码:e0长度:4 mm
湿度敏感等级:3功能数量:1
端子数量:20最高工作温度:85 °C
最低工作温度:-40 °C封装主体材料:UNSPECIFIED
封装代码:HVQCCN封装形状:SQUARE
封装形式:CHIP CARRIER, HEAT SINK/SLUG, VERY THIN PROFILE峰值回流温度(摄氏度):240
座面最大高度:1 mm最大供电电压:3.47 V
最小供电电压:3.13 V标称供电电压:3.3 V
表面贴装:YES温度等级:INDUSTRIAL
端子面层:TIN LEAD端子形式:NO LEAD
端子节距:0.5 mm端子位置:QUAD
处于峰值回流温度下的最长时间:NOT SPECIFIED宽度:4 mm

AD8324ACP-REEL7 数据手册

 浏览型号AD8324ACP-REEL7的Datasheet PDF文件第10页浏览型号AD8324ACP-REEL7的Datasheet PDF文件第11页浏览型号AD8324ACP-REEL7的Datasheet PDF文件第12页浏览型号AD8324ACP-REEL7的Datasheet PDF文件第13页浏览型号AD8324ACP-REEL7的Datasheet PDF文件第15页浏览型号AD8324ACP-REEL7的Datasheet PDF文件第16页 
AD8324  
OVERSHOOT ON PC PRINTER PORTS  
CONTROLLING GAIN/ATTENUATION  
OF THE AD8324  
The data lines on some PC parallel printer ports have excessive  
overshoot, which may cause communications problems when  
presented to the CLK pin of the AD8324. The evaluation board  
was designed to accommodate a series resistor and shunt  
capacitor (R9 and C5 in Figure 29) to filter the CLK signal if  
required. For parallel ports with logic levels above 3.3 V, R9 and  
C5 may be used as an attenuator.  
The slide bar controls the gain/attenuation of the AD8324,  
which is displayed in dB and in V/V. The gain scales 1 dB per  
LSB. The gain code from the position of the slide bar is  
displayed in decimal, binary, and hexadecimal (Figure 28).  
INSTALLING VISUAL BASIC CONTROL SOFTWARE  
Install the CabDrive_24 software by running the setup.exe file  
on disk one of the AD8324 evaluation software. Follow the on-  
screen directions and insert disk two when prompted. Choose  
the installation directory and then select the icon in the upper  
left to complete the installation.  
RUNNING AD8324 SOFTWARE  
To load the control software, go to START, PROGRAMS,  
CABDRIVE_24 or select the AD8324.exe file from the installed  
directory. Once loaded, select the proper parallel port to  
communicate with the AD8324 (Figure 27).  
Figure 28. Control Software Interface  
TRANSMIT ENABLE AND SLEEP MODE  
The Transmit Enable and Transmit Disable buttons select the  
mode of operation of the AD8324 by asserting logic levels on  
the asynchronous TXEN pin. The Transmit Disable button  
applies Logic 0 to the TXEN pin, disabling forward transmis-  
sion. The Transmit Enable button applies Logic 1 to the TXEN  
pin, enabling the AD8324 for forward transmission. Checking  
the Enable SLEEP Mode checkbox applies Logic 0 to the asyn-  
SLEEP  
SLEEP  
chronous  
pin, setting the AD8324 for  
mode.  
Figure 27. Parallel Port Selection  
MEMORY FUNCTIONS  
The Memory section of the software provides a way to alternate  
between two gain settings. The X–>M1 button stores the  
current value of the gain slide bar into memory, while the RM1  
button recalls the stored value, returning the gain slide bar to  
the stored level. The same applies to the X–>M2 and RM2  
buttons.  
Rev. 0 | Page 14 of 16  
 
 
 

与AD8324ACP-REEL7相关器件

型号 品牌 获取价格 描述 数据表
AD8324ACPZ ADI

获取价格

3.3 V Upstream Cable Line Driver
AD8324ACPZ-REEL7 ADI

获取价格

3.3 V Upstream Cable Line Driver
AD8324JRQ ADI

获取价格

3.3 V Upstream Cable Line Driver
AD8324JRQ-EVAL ADI

获取价格

3.3 V Upstream Cable Line Driver
AD8324JRQ-REEL ADI

获取价格

3.3 V Upstream Cable Line Driver
AD8324JRQ-REEL7 ADI

获取价格

3.3 V Upstream Cable Line Driver
AD8324JRQZ ADI

获取价格

3.3 V Upstream Cable Line Driver
AD8324JRQZ-REEL ADI

获取价格

3.3 V Upstream Cable Line Driver
AD8324JRQZ-REEL7 ADI

获取价格

3.3 V Upstream Cable Line Driver
AD8325 ADI

获取价格

5 V CATV Line Driver Fine Step Output Power Control