TPA2000D1
2-W FILTERLESS MONO CLASS-D AUDIO POWER AMPLIFIER
SLOS328B – JUNE 2000 – REVISED MAY 2001
PW PACKAGE
(TOP VIEW)
Modulation Scheme Optimized to Operate
Without a Filter
2 W Into a 4-Ω Speaker (THD+N<1%)
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
INP
INN
SHUTDOWN
GAIN0
BYPASS
AGND
COSC
ROSC
<0.2% THD+N at 1.5 W, 1 kHz, Into a 4-Ω
Load
Extremely Efficient Third Generation 5-V
Class-D Technology:
– Low-Supply Current (No Filter) . . . 4 mA
– Low-Supply Current (Filter) . . . 7.5 mA
– Low-Shutdown Current . . . 0.05 µA
GAIN1
V
DD
PV
PV
DD
OUTN
PGND
DD
OUTP
PGND
– Low-Noise Floor . . . 40 µV
RMS
MicroStar Junior (GQC) Package
(TOP VIEW)
(No-Weighting Filter)
– Maximum Efficiency Into 8 Ω, 75 – 85 %
– 4 Internal Gain Settings . . . 6 – 23.5 dB
– PSSR . . . –77 dB
INP
AGND BYPASS
A2
A6
A1
B1
C1
D1
E1
F1
G1
A7
INN
SHUTDOWN
GAIN0
NC
COSC
ROSC
B7
C7
D7
E7
F7
G7
Integrated Depop Circuitry
Short-Circuit Protection (Short to Battery,
Ground, and Load)
V
DD
GAIN1
PV
PV
OUTP
PV
PV
OUTN
DD
DD
DD
DD
–40°C to 85°C Operating Temperature
Range
PGND
(SIDE VIEW)
description
The TPA2000D1 is a 2-W mono bridge-tied-load
(BTL) class-D amplifier designed to drive a
speaker with at least 4-Ω impedance. The
amplifier uses TI’s third generation modulation
technique, which results in improved efficiency
NC – No internal connection, still requires a pad for the ball.
NOTE: The shaded terminals are used for thermal
connections to the ground plane.
and SNR. It also allows the device to be connected directly to the speaker without the use of the LC output filter
commonly associated with class-D amplifiers (this will result in EMI which must be shielded at the system level).
These features make the device ideal for use in devices where high-efficiency is needed to extend battery run
time.
The gain of the amplifier is controlled by two input terminals, GAIN1, and GAIN0. This allows the amplifier to
be configured for a gain of 6, 12, 18, and 23.5 dB. The differential input terminals are high-impedance CMOS
inputs, and can be used as summing nodes.
The class-D BTL amplifier includes depop circuitry to reduce the amount of turnon pop at power up, and when
cycling SHUTDOWN.
The TPA2000D1 is available in the 16-pin TSSOP package (PW) which is capable of driving 2-W continuous
output power level into a 4-Ω load. TPA2000D1 operates over an ambient temperature range of –40°C to 85°C.
AVAILABLE OPTIONS
PACKAGED DEVICES
T
A
†
TSSOP (PW)
TPA2000D1PW
GQC
–40°C to 85°C
TPA2000D1GQC
†
ThePW package is available taped and reeled. Toorderatapedandreeled
part, add the suffix R to the part number (e.g., TPA2000D1PWR).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
MicroStar Junior is a trademark of Texas Instruments.
Copyright 2001, Texas Instruments Incorporated
This document contains information on products in more than one phase
of development. The status of each device is indicated on the page(s)
specifying its electrical characteristics.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265