5秒后页面跳转
STPM01_11 PDF预览

STPM01_11

更新时间: 2024-11-29 12:23:07
品牌 Logo 应用领域
意法半导体 - STMICROELECTRONICS /
页数 文件大小 规格书
60页 1239K
描述
Programmable single phase energy metering IC with tamper detection

STPM01_11 数据手册

 浏览型号STPM01_11的Datasheet PDF文件第2页浏览型号STPM01_11的Datasheet PDF文件第3页浏览型号STPM01_11的Datasheet PDF文件第4页浏览型号STPM01_11的Datasheet PDF文件第5页浏览型号STPM01_11的Datasheet PDF文件第6页浏览型号STPM01_11的Datasheet PDF文件第7页 
STPM01  
Programmable single phase energy metering IC  
with tamper detection  
Features  
Active, reactive, apparent energies and RMS  
values  
Ripple free active energy pulsed output  
Live and neutral monitoring for tamper  
detection  
Easy and fast digital calibration in only one  
TSSOP20  
point over the whole current range  
OTP for calibration and configuration  
Integrated linear VREGs for digital and analog  
supply  
dedicated command set. The configured bits are  
used for testing, configuration and calibration  
purpose. From a pair of Δ output signals coming  
from analog section, a DSP unit computes the  
amount of consummated active, reactive and  
apparent energy, RMS and instantaneous values  
of voltage and current. The results of computation  
are available as pulse frequency and states on  
the digital outputs of the device or as data bits in a  
data stream, which can be read from the device  
by means of SPI interface. This system bus  
interface is used also during production testing of  
the device and/or for temporary or permanent  
programming of bits of internal OTP. In the  
STPM01 an output signal with pulse frequency  
proportional to energy is generated, this signal is  
used in the calibration phase of the energy meter  
application allowing a very easy approach. When  
the device is fully configured and calibrated, a  
dedicated bit of OTP block can be written  
permanently in order to prevent accidental  
entering into some test mode or changing any  
configuration bit.  
Selectable RC or crystal oscillator  
Support 50 ÷ 60 Hz – IEC62052-11, IEC62053-  
2x specification  
Less than 0.1 % error  
Precision voltage reference: 1.23 V and 30  
ppm/°C max  
Description  
The STPM01 is designed for effective  
measurement of active, reactive and apparent  
energy in a power line system using Rogowski  
coil, current transformer and shunt sensors. This  
device can be implemented as a single chip  
monophase energy meter or as a peripheral  
measurement in a microcontroller based  
monophase or 3-phase energy meter. The  
STPM01 consists, essentially, of two parts: the  
analog part and the digital part. The former, is  
st  
composed by preamplifier and 1 order Δ A/D  
converter blocks, band gap voltage reference, low  
drop voltage regulator, the latter, is composed by  
system control, oscillator, hard wired DSP and  
SPI interface. There is also an OTP block, which  
is controlled through the SPI by means of a  
Table 1.  
Order code  
STPM01FTR  
Device summary  
Temperature range  
Package  
Packaging  
- 40 to 85 °C  
TSSOP20 (tape and reel)  
2500 parts per reel  
June 2011  
Doc ID 10853 Rev 8  
1/60  
www.st.com  
60  
 

与STPM01_11相关器件

型号 品牌 获取价格 描述 数据表
STPM01FTR STMICROELECTRONICS

获取价格

Programmable single phase energy metering IC
STPM066S STMICROELECTRONICS

获取价格

PMIC for ADAS applications
STPM10 STMICROELECTRONICS

获取价格

Programmable single-phase energy metering IC with tamper detection
STPM10BTR STMICROELECTRONICS

获取价格

具有篡改检测功能的可编程单相电能计量IC
STPM11 STMICROELECTRONICS

获取价格

Single phase energy metering IC with pulsed output and digital calibration
STPM11_08 STMICROELECTRONICS

获取价格

Single phase energy metering IC with pulsed output and digital calibration
STPM11ATR STMICROELECTRONICS

获取价格

Single phase energy metering IC with pulsed output and digital calibration
STPM12 STMICROELECTRONICS

获取价格

Single phase energy metering IC with pulsed output and digital calibration
STPM12ATR STMICROELECTRONICS

获取价格

Single phase energy metering IC with pulsed output and digital calibration
STPM13 STMICROELECTRONICS

获取价格

Single phase energy metering IC with pulsed output and digital calibration