5秒后页面跳转
STPM01FTR PDF预览

STPM01FTR

更新时间: 2024-11-28 04:01:43
品牌 Logo 应用领域
意法半导体 - STMICROELECTRONICS /
页数 文件大小 规格书
56页 777K
描述
Programmable single phase energy metering IC

STPM01FTR 数据手册

 浏览型号STPM01FTR的Datasheet PDF文件第2页浏览型号STPM01FTR的Datasheet PDF文件第3页浏览型号STPM01FTR的Datasheet PDF文件第4页浏览型号STPM01FTR的Datasheet PDF文件第5页浏览型号STPM01FTR的Datasheet PDF文件第6页浏览型号STPM01FTR的Datasheet PDF文件第7页 
STPM01  
Programmable single phase energy metering IC  
with tamper detection  
Feature summary  
Active, reactive, apparent energies and RMS  
values  
Ripple free active energy pulsed output  
Live and neutral monitoring for tamper  
detection  
TSSOP20  
Easy and fast digital calibration in only one  
point over the whole current range  
system control, oscillator, hard wired DSP and  
SPI interface.  
OTP for calibration and configuration  
Integrated linear VREGS for digital and analog  
supply  
There is also an OTP block, which is controlled  
through the SPI by means of a dedicated  
command set. The configured bits are used for  
testing, configuration and calibration purpose.  
From a pair of output signals coming from  
analog section, a DSP unit computes the amount  
of consummated active, reactive and apparent  
energy, RMS and instantaneous values of voltage  
and current. The results of computation are  
available as pulse frequency and states on the  
digital outputs of the device or as data bits in a  
data stream, which can be read from the device  
by means of SPI interface. This system bus  
interface is used also during production testing of  
the device and/or for temporary or permanent  
programming of bits of internal OTP. In the  
STPM01 an output signal with pulse frequency  
proportional to energy is generated, this signal is  
used in the calibration phase of the energy meter  
application allowing a very easy approach. When  
the device is fully configured and calibrated, a  
dedicated bit of OTP block can be written  
permanently in order to prevent accidental  
entering into some test mode or changing any  
configuration bit.  
Selectable RC or crystal oscillator  
Support 50÷60 HZ – IEC62052-11, IEC62053-  
2x specification  
Less than 0.1% error  
Precision voltage reference:  
1.23V and 30 ppm/°C Max  
Description  
The STPM01 is designed for effective  
measurement of active, reactive and apparent  
energy in a power line system using Rogowski  
Coil, Current Transformer and Shunt sensors.  
This device can be implemented as a single chip  
1-phase energy meter or as a peripheral  
measurement in a microcontroller based 1-phase  
or 3-phase energy meter. The STPM01 consists,  
essentially, of two parts: the analog part and the  
digital part. The former, is composed by  
preamplifier and 1st order A/D converter  
blocks, Band gap voltage reference, Low drop  
voltage regulator, the latter, is composed by  
Order code  
Part number  
Temperature range  
Package  
Packaging  
STPM01FTR  
-40 to 85 °C  
TSSOP20 (Tape & reel)  
2500 parts per reel  
February 2007  
Rev. 4  
1/56  
www.st.com  
56  

与STPM01FTR相关器件

型号 品牌 获取价格 描述 数据表
STPM066S STMICROELECTRONICS

获取价格

PMIC for ADAS applications
STPM10 STMICROELECTRONICS

获取价格

Programmable single-phase energy metering IC with tamper detection
STPM10BTR STMICROELECTRONICS

获取价格

具有篡改检测功能的可编程单相电能计量IC
STPM11 STMICROELECTRONICS

获取价格

Single phase energy metering IC with pulsed output and digital calibration
STPM11_08 STMICROELECTRONICS

获取价格

Single phase energy metering IC with pulsed output and digital calibration
STPM11ATR STMICROELECTRONICS

获取价格

Single phase energy metering IC with pulsed output and digital calibration
STPM12 STMICROELECTRONICS

获取价格

Single phase energy metering IC with pulsed output and digital calibration
STPM12ATR STMICROELECTRONICS

获取价格

Single phase energy metering IC with pulsed output and digital calibration
STPM13 STMICROELECTRONICS

获取价格

Single phase energy metering IC with pulsed output and digital calibration
STPM13ATR STMICROELECTRONICS

获取价格

Single phase energy metering IC with pulsed output and digital calibration