SN74LVCH244A-Q1
OCTAL BUFFER/DRIVER
WITH 3-STATE OUTPUTS
www.ti.com
SCES492A–SEPTEMBER 2003–REVISED DECEMBER 2005
FEATURES
DW OR PW PACKAGE
(TOP VIEW)
(1)
•
•
•
Qualification in Accordance With AEC-Q100
Qualified for Automotive Applications
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
1OE
1A1
2Y4
1A2
2Y3
1A3
2Y2
1A4
2Y1
GND
V
CC
Customer-Specific Configuration Control Can
Be Supported Along With Major-Change
Approval
2OE
1Y1
2A4
1Y2
2A3
1Y3
2A2
1Y4
2A1
•
ESD Protection Exceeds 2000 V Per
MIL-STD-883, Method 3015; Exceeds 200 V
Using Machine Model (C = 200 pF, R = 0)
•
•
•
•
Operates From 2 V to 3.6 V
Inputs Accept Voltages to 5.5 V
Max tpd of 6.5 ns at 3.3 V
Typical VOLP (Output Ground Bounce)
<0.8 V at VCC = 3.3 V, TA = 25°C
•
•
Typical VOHV (Output VOH Undershoot)
>2 V at VCC = 3.3 V, TA = 25°C
Supports Mixed-Mode Signal Operation on All
Ports (5-V Input/Output Voltage With
3.3-V VCC
)
•
•
Ioff Supports Partial-Power-Down Mode
Operation
Bus Hold on Data Inputs Eliminates the Need
for External Pullup/Pulldown Resistors
(1) Contact factory for details. Q100 qualification data available
on request.
DESCRIPTION/ORDERING INFORMATION
The SN74LVCH244A octal buffer/line driver is designed for 2.7-V to 3.6-V VCC operation.
This device is organized as two 4-bit line drivers with separate output-enable (OE) inputs. When OE is low, this
devices passes data from the A inputs to the Y outputs. When OE is high, the outputs are in the high-impedance
state.
Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors
with the bus-hold circuitry is not recommended.
Inputs can be driven from either 3.3-V or 5-V devices. This feature allows the use of this device as a translator in
a mixed 3.3-V/5-V system environment.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down.
To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
ORDERING INFORMATION
TA
PACKAGE(1)
Reel of 2000
Reel of 2000
ORDERABLE PART NUMBER
SN74LVCH244AQDWRQ1
SN74LVCH244AQPWRQ1
TOP-SIDE MARKING
LH244AQ
LH244AQ
SOIC – DW
–40°C to 125°C
TSSOP – PW
(1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2003–2005, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.