SiJH5700E
Vishay Siliconix
www.vishay.com
N-Channel 150 V (D-S) 175 °C MOSFET
FEATURES
• TrenchFET® Gen V power MOSFET
PowerPAK® 8 x 8L
• Fully lead (Pb)-free device
• Very low RDS x Qg figure of merit (FOM)
• Up to 174 A maximum continuous drain current
• 50 % smaller footprint than D2PAK (TO-263)
• 100 % Rg and UIS tested
D
G
1
S
2
S
S
3
S
S
4
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
S
G
1
Top View
Bottom View
D
APPLICATIONS
PRODUCT SUMMARY
VDS (V)
RDS(on) max. (Ω) at VGS = 10 V
• Synchronous rectification
• OR-ing
150
0.0041
0.0044
93
G
• Motor drive control
RDS(on) max. (Ω) at VGS = 7.5 V
• Battery management
Qg typ. (nC)
ID (A) a
N-Channel MOSFET
S
174
Configuration
Single
ORDERING INFORMATION
Package
PowerPAK 8 x 8L
Lead (Pb)-free and halogen-free
SIJH5700E-T1-GE3
ABSOLUTE MAXIMUM RATINGS (TA = 25 °C, unless otherwise noted)
PARAMETER
SYMBOL
LIMIT
UNIT
Drain-source voltage
Gate-source voltage
VDS
150
20
V
VGS
T
C = 25 °C
174
138
17 b
TC = 70 °C
TA = 25 °C
TA = 70 °C
Continuous drain current (TJ = 175 °C)
ID
15 b
A
Pulsed drain current (t = 100 μs)
IDM
IS
500
303
3 b
TC = 25 °C
TA = 25 °C
Continuous source-drain diode current
Single pulse avalanche current
Single pulse avalanche energy
IAS
EAS
40
80
333
233
L = 0.1 mH
mJ
W
TC = 25 °C
TC = 70 °C
TA = 25 °C
TA =70 °C
Maximum power dissipation
PD
3.3 b
2.3 b
-55 to +175
260
Operating junction and storage temperature range
Soldering recommendations (peak temperature) c
TJ, Tstg
°C
THERMAL RESISTANCE RATINGS
PARAMETER
Maximum junction-to-ambient b
Maximum junction-to-case (drain)
SYMBOL
RthJA
RthJC
TYPICAL
36
0.36
MAXIMUM
45
UNIT
Steady state
Steady state
°C/W
0.45
Notes
a. TC = 25 °C
b. Surface mounted on 1" x 1" FR4 board
c. See solder profile (www.vishay.com/doc?73257). The PowerPAK 8 x 8L is a leadless package. The end of the lead terminal is exposed
copper (not plated) as a result of the singulation process in manufacturing. A solder fillet at the exposed copper tip cannot be guaranteed
and is not required to ensure adequate bottom side solder interconnection
d. Rework conditions: manual soldering with a soldering iron is not recommended for leadless components
S22-0138-Rev. A, 14-Feb-2022
Document Number: 62052
1
For technical questions, contact: pmostechsupport@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000