CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Radial Lead Type, Higher Capacitance
PLG
Higher Capacitance, Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type :
Lead free flow soldering condition correspondence
Compliant to the RoHS directive (2011/65/EU).
PLG
Higher
Capacitance
PLF
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Tangent of loss angle (tan δ)
–55 to +105°C
2.5 to 16V
330 to 3900µF
20% at 120Hz, 20°C
Less than or equal to the specified value
Less than or equal to the specified value
120Hz, 20°C
at
at
(
1)
ESR
100kHz, 20°C
Leakage Current ( 2)
Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25 (100kHz)
Z–55°C / Z+20°C 1.25
Capacitance change
Within 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
tan δ
Endurance
(
1)
ESR
Leakage current ( 2)
Capacitance change
Within 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Damp Heat
tan δ
(
1)
ESR
(Steady State)
Leakage current ( 2)
Capacitance change
Within 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
After soldering the capacitor under the soldering conditions prescribed
here as preheat at 150 to 200°C for 60 to 180 seconds and peak
temperature at 265°C for 10 seconds or less, the capacitor shall meet
the specifications listed at right, provided that its temperature profile is
measured at both of terminal ends facing the soldering side.
tan δ
Resistance to
Soldering Heat
(
1)
ESR
Leakage current ( 2)
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 4V 1200µF)
Resin coated Case
Capacitance
1
2
3
4
5
6
7
8
9 10 11 12
Voltage(g:4V)
P L G 0 G 1 2 2 M C O 1
Size code
Configuration
Capacitance tolerance ( 20%)
φd
Series
Lot. No.
Rated capacitance
(
1200µF
)
)
+0.5MAX.
15MIN
4MIN
L
Rated voltage
(
4V
(mm)
Series name
Type
φ8 × 9L φ8 × 12L φ10
×
13L
Size
φD
L
8.0
8.5
3.5
0.6
8.0
11.5
3.5
10.0
Voltage
12.5
5.0
V
2.5
e
4
6.3
j
10
A
16
C
P
Code
g
0.6
0.6
φd
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
54
CAT.8100F