Datasheet > MAX15093AEVKIT

MAX15093AEVKIT

更新时间： 2024-09-16 02:52:51

品牌	Logo	应用领域
美信 - MAXIM		/
页数	文件大小	规格书
9页	408K
描述
Banana Jacks for Input and Output Voltage

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

MAX15093AEVKIT 数据手册

Evaluate: MAX15093/MAX15093A

MAX15093/MAX15093A

Evaluation Kits

General Description

Quick Start

The MAX15093/MAX15093A evaluation kits (EV kits)

provide a proven design to evaluate the MAX15093/

MAX15093A hot-swap controllers with an integrated 15A

MOSFET. The EV kits are configured to pass 15A in a

2.7V to 18V hot-swap application, thus providing a fully

integrated solution. The EV kits use the MAX15093GWL+/

MAX15093AGWL+T in a 2.57mm x 4.03mm, 40-bump,

0.5mm pitch wafer-level package (WLP) with a proven

four-layer PCB design. As configured, the EV kits are

optimized to operate at 12V.

Required Equipment

● MAX15093 or MAX15093A EV kit

● 12V, 15A DC power supply

● Voltmeter

Procedure

The EV kits are fully assembled and tested. Follow the

steps below to verify board operation. Caution: Do not

turn on the power supply until all connections are

completed.

The two EV kit versions (MAX15093AEVKIT# and

MAX15093EVKIT#) are built on the same PCB fabrication

and can be used interchangeably to evaluate either the

MAX15093 or MAX15093A by replacing U1 with the

desired device.

1) Verify that a shunt is installed across pins 1-2 on the

following jumpers: J1, J3, J4, J5, UV_IN, and CB.

2) Turn on the power supply and set the supply to 12V,

then disable the power supply.

3) Connect the positive terminal of the power supply

to the IN banana jack on the EV kits. Connect the

negative terminal of the power supply to the GND

banana jack.

Features

● 2.7V to 18V Operating-Voltage Range

● Up to 15A Configurable Load-Current Capability

● Banana Jacks for Input and Output Voltage

● Programmable Slew-Rate Control

● Selectable/Configurable Circuit-Breaker Threshold

● Configurable Overvoltage/Undervoltage Lockout

● Programmable Timeout Delay

4) Enable the power supply.

5) Verify that the voltage between the OUT and GND

banana jacks is 12V.

6) Verify that the internal regulator voltage (REG) is 3.3V.

7) The EV kits are now ready for additional evaluation.

● FAULT and PG Outputs

● Defined Safe Operation Area

● Proven PCB Layout

Ordering Information appears at end of data sheet.

● Fully Assembled and Tested

19-8764; Rev 1; 7/19

12 3 4 5 6 7...9

中文翻译

下载PDF

与MAX15093AEVKIT相关器件

型号	品牌	获取价格	描述	数据表
MAX15093AGWL+T	MAXIM	获取价格	Power Supply Support Circuit,
MAX15095	MAXIM	获取价格	2.7V to 18V Operating Voltage Range
MAX15095	ADI	获取价格	2.7V至18V、6.6A、集成热插拔/电子断路器
MAX15095A	MAXIM	获取价格	2.7V to 18V Operating Voltage Range
MAX15095A	ADI	获取价格	2.7V至18V、6.6A、集成热插拔/电子断路器
MAX15095AEVKIT	MAXIM	获取价格	2.7V to 18V Operating Voltage Range
MAX15095AGFC+	MAXIM	获取价格	Power Management Circuit,
MAX15095D	MAXIM	获取价格	2.7V to 18V Operating Voltage Range
MAX15095D	ADI	获取价格	2.7V至18V、6.6A、集成热插拔/电子断路器
MAX15095DGFC+	MAXIM	获取价格	Power Management Circuit,