Rad Hard and SEE Hard 12A Synchronous Buck
Regulator with Multi-Phase Current Sharing
ISL70002SEH
Features
The ISL70002SEH is a radiation hardened and SEE hardened
high efficiency monolithic synchronous buck regulator with
integrated MOSFETs. This single chip power solution operates
over an input voltage range of 3V to 5.5V and provides a tightly
regulated output voltage that is externally adjustable from 0.8V
to ~85% of the input voltage. Output load current capacity is
• DLA SMD 5962-12202
• 12A output current for a single device (at T = +150°C)
J
• 14A output current for a single device (at T = +125°C)
J
• 19A output current for two paralleled devices
• Available in a thermally enhanced heatsink package - R64.C
• 1MHz or 500kHz switching frequency
• 3V to 5.5V supply voltage range
12A for T ≤ +150°C. The two ISL70002SEH devices configured
J
to current share can provide 19A total output current, assuming
±27% worst-case current share accuracy.
• ±1% Ref. voltage (line, load, temp. & rad)
• Pre-biased load compatible
The ISL70002SEH utilizes peak current-mode control with
integrated error amp compensation and pin selectable slope
compensation. Switching frequency is also pin selectable to
either 1MHz or 500kHz. Two devices can be synchronized 180°
out-of-phase to reduce input RMS ripple current.
• Redundancy/junction isolation: Exceptional SET performance
• Excellent transient response
• High efficiency > 90%
High integration makes the ISL70002SEH an ideal choice to
power small form factor applications. Two devices can be
synchronized to provide a complete power solution for large
scale digital ICs, like field programmable gate arrays (FPGAs)
that require separate core and I/O voltages.
• Two ISL70002SEH synchronization, inverted-phase
• Comparator input for enable and power-good
• Input undervoltage, output undervoltage and adjustable
Output overcurrent protection
• QML qualified per MIL-PRF-38535
Applications
• FPGA, CPLD, DSP, CPU Core and I/O Voltages
• Full Mil-temp range operation (-55°C to +125°C)
• Radiation environment
• Low-voltage, High-density Distributed power systems
- High dose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 krad(Si)
- ELDRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 krad(Si)*
*Level guaranteed by characterization; “EH” version is
production tested to 50 krad(Si).
• SEE hardness
2
- SEL and SEB LET . . . . . . . . . . . . . . . . 86.4MeV/mg/cm
TH
- SEFI LET . . . . . . . . . . . . . . . . . . . . . . . . . . 43MeV/mg/cm
2
TH
2
- SET LET . . . . . . . . . . . . . . . . . . . . . . . . 86.4MeV/mg/cm
TH
90
85
80
75
70
25
CH1 MASTER LX + 20V
20
15
CH2 SLAVE LX + 15V
10
CH3 VOUT x 10
5
CH4 SYNC
0
-6
-4
-2
0
2
4
6
8
10
12
14
TIME (µs)
0
1
2
3
4
5
6
7
8
9
10 11 12
LOAD CURRENT (A)
2
FIGURE 2. 2-PHASE SET PERFORMANCE at 86.4MeV/mg/cm
FIGURE 1. EFFICIENCY 5V INPUT TO 2.5V OUTPUT, T = +25°C
A
July 12, 2013
FN8264.3
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2012, 2013. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
1