Rad Hard and SEE Hard 6A Synchronous Buck Regulator
ISL70001ASEH
Features
The ISL70001ASEH is a radiation hardened and SEE hardened
high efficiency monolithic synchronous buck regulator with
integrated MOSFETs. This single chip power solution operates
over an input voltage range of 3V to 5.5V and provides a tightly
regulated output voltage that is externally adjustable from 0.8V
to ~85% of the input voltage. Output load current capacity is 6A
• ±1% Reference Voltage Over Line, Load, Temperature and
Radiation
• Current Mode Control for Excellent Dynamic Response
• Full Mil-Temp Range Operation (T = -55°C to +125°C)
A
• 50% Lower Shutdown Supply Current than the ISL70001SEH
• Available in a thermally enhanced heatsink package - R48.B
• Highly Efficient: 94% Peak Efficiency
for T < +145°C.
J
The ISL70001ASEH utilizes peak current-mode control for
excellent output load transient response and features integrated
compensation and switches at a fixed frequency of 1MHz to
reduce component size and count. In application where two POLs
are needed, two ISL70001ASEH devices can be synchronized
180° out-of-phase to reduce the overall input RMS ripple current.
The internal synchronous power switches are optimized for high
efficiency and good thermal performance.
• Operates from 3V to 5.5V Supply
• Adjustable Output Voltage
- Two External Resistors Set V
OUT
from 0.8V to ~85% of V
IN
• Bi-directional SYNC Pin Allows Two Devices to be Synchronized
180° Out-of-Phase
• Power-Good Output Voltage Monitor
• Adjustable Analog Soft-Start
The ISL70001ASEH incorporates fault protection for the
regulator. The protection circuits include input undervoltage,
output undervoltage, and output overcurrent.
• Input Undervoltage, Output Undervoltage and Output
Overcurrent Protection
High integration and class leading radiation tolerance makes
the ISL70001ASEH an ideal choice to power many of today’s
small form factor applications. Two devices can be
synchronized to provide a complete power solution for large
scale digital ICs, like field programmable gate arrays (FPGAs),
that require separate core and I/O voltages.
• Electrically Screened to DLA SMD 5962-09225
• QML Qualified per MIL-PRF-38535 Requirements
• Radiation Hardness
- Total Dose [50-300rad(Si)/s] . . . . . . . . . . . . . . 100krad(Si)
- Total Dose [<10mrad(Si)/s] . . . . . . . . . . . . . . 100krad(Si)*
Applications
• FPGA, CPLD, DSP, CPU Core or I/O Voltages
* Product capability established by initial characterization. The
EH version is acceptance tested on a wafer-by-wafer basis to
50krad(Si) at low dose rate.
• Low-Voltage, High-Density Distributed Power Systems
• SEE Hardness
- SEL and SEB LET . . . . . . . . . . . . 86.4MeV/mg/cm min
2
-6
Related Literature
• ISL70001ASEHEV1Z Evaluation Board, AN1842
eff
2
2
- SEFI X-section (LET = 86.4MeV/mg/cm ) 1.4 x 10 cm
eff
max
2
- SET LET (< 1 Pulse Perturbation) 86.4MeV/mg/cm min
eff
100
95
5V Supply
ISL70001ASEH
CORE
AUX
I/O
90
SYNCH
85
RAD TOLERANT
FPGA
ISL75051SEH
1.5V
1.8V
3.3V
2.5V
80
75
70
1.2V
ISL70001ASEH
SYNCH
0
1
2
3
4
5
6
LOAD CURRENT (A)
FIGURE 1. TYPICAL APPLICATION
FIGURE 2. EFFICIENCY 5V INPUT, T = +25°C
A
May 22, 2013
FN8365.0
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 |Copyright Intersil Americas LLC 2013. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
1