DATASHEET
ISL70001SEH, ISL70001SRH
Radiation Hardened and SEE Hardened 6A Synchronous Buck Regulator
FN7956
Rev 3.02
Sep 16, 2022
The ISL70001SEH, ISL70001SRH are radiation hardened and
Features
SEE hardened high efficiency monolithic synchronous buck
• ±1% reference voltage over line, load, temperature and
radiation
regulators with integrated MOSFETs. This single chip power
solution operates over an input voltage range of 3V to 5.5V
and provides a tightly regulated output voltage that is
externally adjustable from 0.8V to ~85% of the input voltage.
• Current mode control for excellent dynamic response
• Full Mil-temp range operation (T = -55°C to +125°C)
A
Output load current capacity is 6A for T < +145°C.
J
• High efficiency >90%
High integration and class leading radiation tolerance makes
the ISL70001SEH, ISL70001SRH ideal choices to power
many of today’s small form factor applications. Two devices
can be synchronized to provide a complete power solution for
large scale digital ICs, like field programmable gate arrays
(FPGAs) that require separate core and I/O voltages.
• Fixed 1MHz operating frequency
• Available in a thermally enhanced heatsink package - R48.B
• Operates from 3V to 5.5V supply
• Adjustable output voltage
- Two external resistors set V
from 0.8V to ~85% of V
IN
OUT
In applications where the ENABLE input is tied high to PVIN we
recommend that the input voltage ramp rate be equal to or
greater than 10V/ms. This is to prevent unwanted voltage from
prematurely appearing on the output.
• Bidirectional SYNC pin allows two devices to be
synchronized 180° out-of-phase
• Starts into prebiased load
• Power-good output voltage monitor
• Adjustable analog soft-start
For a PVIN voltage that has a slower ramp rate or is stepped up
we recommend use of the ISL70001ASEH. Ensuring that the
ENABLE input is held low until the chosen VINPOR is satisfied
will prevent this ‘false start’.
• Input undervoltage, output undervoltage and output
overcurrent protection
• Electrically screened to DLA SMD 5962-09225
• QML qualified per MIL-PRF-38535 requirements
Applications
• FPGA, CPLD, DSP, CPU core or I/O voltages
• Radiation acceptance testing - ISL70001SEH
- HDR (50-300rad(Si)/s): 100krad(Si) (min)
- LDR (<10mrad(Si)/s): 50krad(Si) (min)
• Radiation acceptance testing - ISL70001SRH
- HDR (50-300rad(Si)/s): 100krad(Si) (min)
• SEE hardness (see SEE report for details)
• Low-voltage, high-density distributed power systems
2
- SEL and SEB LET . . . . . . . . . . . 86.4MeV/mg/cm (min)
eff
2
-6
- SEFI X-section (LET = 86.4MeV/mg/cm ) 1.4 x 10
eff
2
cm (max)
2
- SET LET (<1 pulse perturbation) 86.4MeV/mg/cm
eff
(min)
95
90
85
80
75
70
5V SUPPLY
ISL70001SEH
CORE
AUX
I/O
SYNCH
RAD TOLERANT
FPGA
ISL75051SEH
ISL70001SEH
SYNCH
0
1
2
3
4
5
6
LOAD CURRENT (A)
FIGURE 1. TYPICAL APPLICATION
FIGURE 2. EFFICIENCY 5V INPUT TO 3.3V OUTPUT, T = +25°C
A
FN7956 Rev 3.02
Sep 16, 2022
Page 1 of 23
© 2011-2022 Renesas Electronics