IS43/46TR16640C, IS43/46TR16640CL
IS43/46TR81280C, IS43/46TR81280CL
128MX8, 64MX16 1Gb DDR3 SDRAM
DECEMBER 2020
FEATURES
Standard Voltage: VDD and VDDQ = 1.5V ± 0.075V
Partial Array Self Refresh
Asynchronous RESET pin
Low Voltage (L): VDD and VDDQ = 1.35V + 0.1V, -0.067V
- Backward compatible to 1.5V
High speed data transfer rates with system
frequency up to 933 MHz
TDQS (Termination Data Strobe) supported (x8
only)
8 internal banks for concurrent operation
8n-bit pre-fetch architecture
OCD (Off-Chip Driver Impedance Adjustment)
Dynamic ODT (On-Die Termination)
Driver strength : RZQ/7, RZQ/6 (RZQ = 240 )
Write Leveling
Programmable CAS Latency
Programmable Additive Latency: 0, CL-1,CL-2
Programmable CAS WRITE latency (CWL) based
on tCK
Up to 200 MHz in DLL off mode
Operating temperature:
Programmable Burst Length: 4 and 8
Commercial (TC = 0°C to +95°C)
Industrial (TC = -40°C to +95°C)
Automotive, A1 (TC = -40°C to +95°C)
Automotive, A2 (TC = -40°C to +105°C)
Automotive, A25 (TC = -40°C to +115°C)
Automotive, A3 (TC = -40°C to +125°C)
Programmable Burst Sequence: Sequential or
Interleave
BL switch on the fly
Auto Self Refresh(ASR)
Self Refresh Temperature(SRT)
Refresh Interval:
7.8 µs (8192 cycles/64 ms) Tc= -40°C to 85°C
3.9 µs (8192 cycles/32 ms) Tc= 85°C to 105°C
1.95 µs (8192 cycles/16 ms) Tc= 105°C to 115°C
0.97 µs (8192 cycles/8 ms) Tc= 115°C to 125°C
OPTIONS
ADDRESS TABLE
Parameter
Configuration:
128Mx8
A0-A13
A0-A9
64Mx16
A0-A12
A0-A9
128Mx8
64Mx16
Row Addressing
Column Addressing
Bank Addressing
Page size
Auto Precharge Addressing
BL switch on the fly
Package:
96-ball BGA (9mm x 13mm) for x16
78-ball BGA (8mm x 10.5mm) for x8
BA0-2
1KB
A10/AP
A12/BC#
BA0-2
2KB
A10/AP
A12/BC#
SPEED BIN
Speed Option
125J
107M
Units
JEDEC Speed Grade
DDR3-1600J
DDR3-1866M
CL-nRCD-nRP
tRCD,tRP(min)
10-10-10
12.5
13-13-13
13.91
tCK
ns
Note: Faster speed options may be backward compatible to slower speed options. Refer to timing tables (8.3)
Copyright © 2020 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without
notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the
latest version of this device specification before relying on any published information and before placing orders for products.
Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can
reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such
applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that:
a.) the risk of injury or damage has been minimized;
b.) the user assume all such risks; and
c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances
Integrated Silicon Solution, Inc. – www.issi.com –
1
Rev. B2
12/17/2020