IP series
Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary
Distinctive features and specifications
UG1212-A-R1
K
K
K
K
K
Illuminated or non-illuminated
Tactile feedback
Wide variety of configurations
Flat round actuator for optional marking
Sealed to IP67
B1
ENVIRONMENTAL SPECIFICATIONS
GENERAL SPECIFICATIONS
• Front panel sealing : IP67 according to IEC 60529
IP69K according to DIN 40050-9 (non-illuminated) with cap U5125
• Shock resistance : 100 g according to IEC 512-4, test 6c
• Vibration resistance : 10-500Hz - 10 g according to IEC 512-4, test 6d
• Salt spray : IEC 512-6, test 11f
• Panel thickness : 1,5 mm (.059) min.
4 mm (.157 max.)
• Total travel :
Funct. 3 : 1,7 mm (.067) +/- 0,3 mm
Funct. 5 : 1,3 mm (.051) +/- 0,3 mm
• Typical operating force : 6N +/- 2N
• Low level/mech. life : 1.000.000 cycles
• Torque : 1,5 Nm max. applied to nut
• Soldering : 320°C max. for 3 sec.
• Robustness (non-illuminated) : IK06 according to EN 50102 (1 joule)
• Operating temperature : -40°C to +85°C
ELECTRICAL SPECIFICATIONS
• Max. current/voltage rating with resistive load (gold plated silver contacts):
MATERIALS
5A 28VDC, 70.000 cycles
For W terminals, current has to
0,2A 48VDC, 500.000 cycles
be limited to 400mA.
• Case : thermoplastic UL94-V0
• Actuator : polyamide 6/6
0,5A 48VAC, 500.000 cycles
• Bushing/bezel : zinc die-cast
(zamac), black painted
• Initial contact resistance : 100 mΩ max.
• Insulation resistance : 1 GΩ min. at 500VDC
• Dielectric strength : 1.500 Vrms
• Contacts : silver, gold plated (std)
brass, gold plated (for option 104)
• Contact bounce : 10 ms
• Output wires (flying lead terminals)
:
F version : AWG20, section 0,6 mm2
Wversion:AWG24, section0,23mm2
LED wires :
LED COMPONENT SPECIFICATIONS
LED colour
Super red (L0S)
Yellow (L0Y)
Green (L0G)
Blue (L0B)
Forward current Typ. forward voltage Max. forward voltage
•
20mA
20mA
20mA
20mA
20mA
2,1V
2,1V
2,1V
3,2V
3,35V
2,3V
2,3V
2,3V
3,8V
4,25V
F version : AWG26, section 0,12 mm2
Wversion:AWG24, section0,23mm2
• Lens : polycarbonate
• Terminal seal : epoxy
White (L0W)
AGENCY APPROVAL
A resistor must be series-connected by the user.
2A 125VAC/250VAC
File E83438
supply voltage - LED forward voltage
LED forward current
Resistor value =
See following pages.
MOUNTING
Panel cut-out
Matrix mounting
Back of panel space requirement
20.00
(.787)
20.00
(.787)
12.90
(.507)
1
Ø13.60
(.535DIA)
Ø13.50
(.531DIA)
O-ring
APEM
www.apem.com
B1-15