5秒后页面跳转
HV826 PDF预览

HV826

更新时间: 2024-11-20 22:33:43
品牌 Logo 应用领域
超科 - SUPERTEX 驱动器高压
页数 文件大小 规格书
6页 336K
描述
High Voltage EL Lamp Driver

HV826 数据手册

 浏览型号HV826的Datasheet PDF文件第2页浏览型号HV826的Datasheet PDF文件第3页浏览型号HV826的Datasheet PDF文件第4页浏览型号HV826的Datasheet PDF文件第5页浏览型号HV826的Datasheet PDF文件第6页 
HV826  
High Voltage EL Lamp Driver  
Ordering Information  
Package Options  
SO-8  
Device  
MSOP-8  
Die  
HV826  
HV826MG*  
HV826LG  
HV826X  
* Product supplied on 2500 piece carrier tape reels.  
Features  
General Description  
1.8V to 3.5V operating supply voltage  
The Supertex HV826 is a high voltage driver designed for driving  
EL lamps. The input supply voltage range is from 1.8V to 3.5V.  
The device uses a single inductor and a minimum number of  
passive components.The nominal regulated output voltage that  
is applied to the EL lamp is 80V. The chip can be enabled/  
disabled by connecting the resistor on RSW-OSC to VDD/ground.  
DC to AC conversion  
Adjustable output frequency  
Adjustable switch frequency  
Output voltage regulation  
Enable/disable function  
The HV826 has two internal oscillators, a switching MOSFET,  
and a high voltage EL lamp driver. The frequency for the  
switching MOSFET is set by an external resistor connected  
between the RSW-osc pin and the supply pin VDD. The EL lamp  
driver frequency is set by an external resistor connected be-  
tween REL-osc pin and the VDD pin. An external inductor is  
connected between the LX and VDD pins. A 0.01-0.1µF capacitor  
is connected between CS and ground.The EL lamp is connected  
between VA and VB.  
Applications  
Mobile cellular phones  
Pagers  
The switching MOSFET charges the external inductor and  
discharges it into the capacitor at CS.The voltage at CS will start  
to increase. Once the voltage at CS reaches a nominal value of  
80V, the switching MOSFET is turned OFF to conserve power.  
The outputs VA and VB are configured as an H bridge and are  
switching in opposite states to achieve 160V peak-to-peak  
across the EL lamp.  
Portable Transceivers  
Remote Control Units  
Calculators  
Pin Configuration  
Absolute Maximum Ratings*  
Supply Voltage, VDD  
-0.5V to +4.5V  
Output Voltage, VCs  
-0.5V to +100V  
-25° to +85°C  
-65°C to +150°C  
250mW  
ςΑ  
Operating Temperature Range  
Storage Temperature Range  
MSOP-8 Power Dissipation  
SO-8 Power Dissipation  
VDD  
RSW-osc  
REL-osc  
Gnd  
1
2
3
4
8
7
6
5
VA  
VB  
CS  
LX  
MSOP-8  
and  
SO-8  
400mW  
Note:  
*All voltages are referenced to GND.  
Top View  
11/12/01  
Supertex Inc. does not recommend the use of its products in life support applications and will not knowingly sell its products for use in such applications unless it receives an adequate "products liability  
indemnification insurance agreement." Supertex does not assume responsibility for use of devices described and limits its liability to the replacement of devices determined to be defective due to  
workmanship. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications, refer to the  
Supertex website: http://www.supertex.com. For complete liability information on all Supertex products, refer to the most current databook or to the Legal/Disclaimer page on the Supertex website.  

与HV826相关器件

型号 品牌 获取价格 描述 数据表
HV826LG SUPERTEX

获取价格

High Voltage EL Lamp Driver
HV826LG-G SUPERTEX

获取价格

EL Driver, 1-Segment, PDSO8, 4.90 X 3.90 MM, 1.75 MM HEIGHT, 1.27 MM PITCH, GREEN, MS-012A
HV826LGP030 SUPERTEX

获取价格

EL Driver, PDSO8, SO-8
HV826LGP031 SUPERTEX

获取价格

EL Driver, PDSO8, SO-8
HV826MG SUPERTEX

获取价格

High Voltage EL Lamp Driver
HV826MG-G SUPERTEX

获取价格

暂无描述
HV826X SUPERTEX

获取价格

High Voltage EL Lamp Driver
HV828X SUPERTEX

获取价格

EL Driver, 1-Segment, DIE
HV829A SUPERTEX

获取价格

High Voltage EL Lamp Driver
HV829ASG SUPERTEX

获取价格

High Voltage EL Lamp Driver