5秒后页面跳转
HV832DB1 PDF预览

HV832DB1

更新时间: 2024-11-03 22:33:43
品牌 Logo 应用领域
超科 - SUPERTEX 驱动器
页数 文件大小 规格书
2页 446K
描述
Dual EL Lamp Driver

HV832DB1 数据手册

 浏览型号HV832DB1的Datasheet PDF文件第2页 
HV832DB1  
Dual EL Lamp Driver  
Introduction  
Specifications  
Input Voltage  
3.0V to 4.2V  
40mA Max.  
Up to 2.7in2  
417Hz  
The Supertex HV832DB1 demo board contains all necessary  
circuitry to demonstrate the features of the HV832 dual EL lamp  
driver.  
Supply Current  
Lamp Size Range  
Lamp Frequency  
Converter Frequency  
Simply connect it to a power supply and a lamp as shown below.  
For additional assistance in designing EL driver circuits, please  
refer to application notesAN-H33 (effect of external components  
on performance of Supertex EL drivers), application note AN-  
H44 (HV832 application circuits), and AN-H43 (EL lamp driver  
circuits to reduce lamp audible noise).  
53.4KHz  
Board Layout and Connections  
V
EL2  
Com  
DD  
EL1  
Com  
Re  
CDD  
Ce  
Cs  
HV832  
Diode  
LX  
EN-SW  
V
GND  
IN  
CIN  
VIN Inductor Supply  
Demo Board Connections:  
Control lamp selection/Enable Input (EN-SW)  
Supplies the high voltage power converter. Connect to positive  
terminal of a power supply.  
Various modes of the device are selected via the control pin/EN-  
SW. Each logic pulse applied to the control pin/EN-SW will  
cause the device to change to the next mode. The sequence for  
the modes is: 1) EL1 on, 2) EL2 on, 3) both EL1 and EL2 on, and  
4) device shuts down. This input may be connected to a  
mechanical switch, or to a logic circuit output that has a source  
impedance of less than 20K.  
GND Circuit Ground  
Connect to VDD and VIN negative terminals. Supply bypass  
capacitor for both VDD and VIN are provided on the demo board.  
External supply bypass capacitors are not necessary.  
EL1 and EL2 Lamp Connections  
Connects to lamps 1 and 2. Polarity is irrelevant.  
VDD IC Supply  
Com Lamp Connections  
Supplies the HV832 EL driver IC. The supplied circuit is  
optimized for 3.0 to 4.2 volt operations. Connect to positive  
terminal of a power supply.  
Connectstotheothersideoflamps1and2. Polarityisirrelevant.  
12/14/01  
Supertex Inc. does not recommend the use of its products in life support applications and will not knowingly sell its products for use in such applications unless it receives an adequate "products liability  
indemnification insurance agreement." Supertex does not assume responsibility for use of devices described and limits its liability to the replacement of devices determined to be defective due to  
workmanship. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications, refer to the  
Supertex website: http://www.supertex.com. For complete liability information on all Supertex products, refer to the most current databook or to the Legal/Disclaimer page on the Supertex website.  

与HV832DB1相关器件

型号 品牌 获取价格 描述 数据表
HV832MG SUPERTEX

获取价格

Dual High Voltage, Low Noise EL Lamp Driver
HV832MG-G SUPERTEX

获取价格

EL Driver, 3-Segment, PDSO8, 3 X 3 MM, 1.10 MM HEIGHT, 0.65 MM PITCH, GREEN, MO-187AA, MSO
HV832X SUPERTEX

获取价格

Dual High Voltage, Low Noise EL Lamp Driver
HV833 SUPERTEX

获取价格

High Voltage EL Lamp Driver
HV833 MICROCHIP

获取价格

HV833 is a high voltage driver designed for driving EL lamps of up to 35nF (10-12in2). The
HV833_07 SUPERTEX

获取价格

High Voltage EL Lamp Driver
HV833DB1 SUPERTEX

获取价格

EL Lamp Driver
HV833MG SUPERTEX

获取价格

High Voltage EL Lamp Driver
HV833MG-G SUPERTEX

获取价格

High Voltage EL Lamp Driver
HV833X SUPERTEX

获取价格

High Voltage EL Lamp Driver