5秒后页面跳转
HV829B PDF预览

HV829B

更新时间: 2024-11-03 21:53:43
品牌 Logo 应用领域
超科 - SUPERTEX 驱动器高压
页数 文件大小 规格书
4页 44K
描述
High Voltage EL Lamp Driver

HV829B 数据手册

 浏览型号HV829B的Datasheet PDF文件第2页浏览型号HV829B的Datasheet PDF文件第3页浏览型号HV829B的Datasheet PDF文件第4页 
HV829A/B  
Advance Information  
High Voltage EL Lamp Driver  
Features  
General Description  
Processed with HVCMOS® technology  
The Supertex HV829A/B are high voltage EL lamp driver inte-  
grated circuits designed for driving EL lamps of up to 70nF at  
1000Hz. The input supply voltage range is from 2.7V to 5.5V.  
These devices use a single inductor, a high voltage switching  
FET and a minimum number of passive components. The  
HV829A/B will supply the EL lamp with an AC square wave with  
a peak-to-peak voltage of two times the set regulated DC  
voltage.  
VDD voltage range = 2.7 to 5.5V DC  
Output load up to 70nF (20 in2 for 3.5nF/ in2 lamp)  
Adjustable DC-DC converter frequency  
Continious output voltage regulation control  
(from 50V to 200V)  
The HV829A/B has one internal oscillator and a high voltage EL  
lamp driver. The frequency for the external switching MOSFET  
is set by an external resistor connected between the RSW-osc pin  
and GND. The EL frequency for the HV829A is equal to the  
switchingfrequencydividedby64wheretheELfrequencyforthe  
HV829B is equal to the switching frequency divided by 128. Gate  
of the external MOSFET is connected to the Gate pin. An  
external inductor is connected between the Drain of external  
MOSFET and VDD pin. A 0.01-2.5µF capacitor is connected  
between Cs and ground. The EL lamp is connected between VA  
and VB. The output voltage regulation level is controlled via the  
VREG pin for dimming and/or conservation of power. The output  
voltage regulation can be controlled continuously between 50V  
and 200V depending on the voltage applied to VREG pin (0.75V  
to 3V).  
Application  
Electronic Organizers  
Handheld Portable Computers  
Display Signs  
Portable Instrumentation Equipment  
The switching MOSFET charges the external inductor and  
discharges it into the capacitor at CS. The voltage at CS will start  
to increase. Once the voltage at CS reaches a nominal value  
chosen by the user, the switching MOSFET is turned OFF to  
conserve power. The outputs VA and VB are configured as an H  
bridge and are switching in opposite states to achieve the AC  
voltage of +/- VREG voltage across the EL lamp.  
Typical Application Circuit  
Off=V  
DD  
On=GND  
VDD  
1
2
3
4
8
7
6
5
VDD  
V
V
A
B
EL Lamp  
Lx  
Vreg  
RSW-osc  
VREG  
GND  
Gate  
BAV21  
C
S
HV829ASG  
+
-
VN2224N3 or  
TN2425N8  
C
VIN  
IN  
C
S
250V  
09/05/02  
Supertex Inc. does not recommend the use of its products in life support applications and will not knowingly sell its products for use in such applications unless it receives an adequate "products liability  
indemnification insurance agreement." Supertex does not assume responsibility for use of devices described and limits its liability to the replacement of devices determined to be defective due to  
workmanship. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications, refer to the  
Supertex website: http://www.supertex.com. For complete liability information on all Supertex products, refer to the most current databook or to the Legal/Disclaimer page on the Supertex website.  

与HV829B相关器件

型号 品牌 获取价格 描述 数据表
HV829BSG SUPERTEX

获取价格

High Voltage EL Lamp Driver
HV830 SUPERTEX

获取价格

High Voltage EL Lamp Driver
HV830 MICROCHIP

获取价格

HV830 is a high-voltage driver designed for driving EL lamps of up to 50nF. EL lamps great
HV830_07 SUPERTEX

获取价格

High Voltage EL Lamp Driver IC
HV8308DJ ETC

获取价格

Interface IC
HV8308PJ ETC

获取价格

Interface IC
HV8308X ETC

获取价格

Interface IC
HV830LG SUPERTEX

获取价格

High Voltage EL Lamp Driver
HV830LG-G SUPERTEX

获取价格

High Voltage EL Lamp Driver IC
HV830X SUPERTEX

获取价格

High Voltage EL Lamp Driver