CYS25G0101DX
Pin Descriptions
CYS25G0101DX OC-48 SONET Transceiver
Pin Name I/O Characteristics
Transmit Path Signals
Signal Description
TXD[15:0]
HSTL inputs,
Parallel Transmit Data Inputs. A 16-bit word, sampled by TXCLKI↑. TXD[15] is the most
sampled by TXCLKI↑ significant bit (the first bit transmitted).
TXCLKI
HSTL Clock input Parallel Transmit Data Input Clock. The TXCLKI is used to transfer the data into the input
register of the serializer. The TXCLKI samples the data, TXD [15:0], on the rising edge of
the clock cycle.
TXCLKO
VREF
HSTL Clock output Transmit Clock Output. Divide by 16 of the selected transmit bit-rate clock. It can be used
to coordinate byte-wide transfers between upstream logic and the CYS25G0101DX.
Input Analog
Reference
Reference Voltage for HSTL Parallel Input Bus. VDDQ/2.[3]
Receive Path Signals
RXD[15:0]
HSTL output,
synchronous
Parallel Receive Data Output. These outputs change following RXCLK↓. RXD[15] is the
most significant bit of the output word, and is received first on the serial interface.
RXCLK
HSTL Clock output Receive Clock Output. Divide by 16 of the bit-rate clock extracted from the received serial
stream. RXD [15:0] is clocked out on the falling edge of the RXCLK.
CM_SER
RXCN1
RXCN2
RXCP1
RXCP2
Analog
Analog
Analog
Analog
Analog
Common Mode Termination. Capacitor shunt to VSS for common mode noise.
Receive Loop Filter Capacitor (Negative)
Receive Loop Filter Capacitor (Negative)
Receive Loop Filter Capacitor (Positive)
Receive Loop Filter Capacitor (Positive)
Device Control and Status Signals
REFCLK±
Differential LVPECL Reference Clock. This clock input is used as the timing reference for the transmit and
input
receive PLLs. A derivative of this input clock may also be used to clock the transmit parallel
interface. The reference clock is internally biased allowing for an AC-coupled clock signal.
LFI
LVTTL output
Line Fault Indicator. When LOW, this signal indicates that the selected receive data
stream has been detected as invalid by either a LOW input on SD, or by the receive VCO
being operated outside its specified limits.
RESET
LVTTL input
LVTTL input
Reset for all logic functions except the transmit FIFO.
LOCKREF
Receive PLL Lock to Reference. When LOW, the receive PLL locks to REFCLK instead
of the received serial data stream.
SD
LVTTL input
Signal Detect. When LOW, the receive PLL locks to REFCLK instead of the received serial
data stream. The SD is to be connected to an external optical module to indicate a loss of
received optical power.
FIFO_ERR
LVTTL output
Transmit FIFO Error. When HIGH the transmit FIFO has either under or overflowed. When
this occurs, the FIFO’s internalclearing mechanism willclear the FIFO within 9clock cycles.
In addition, FIFO_RST must be activated at device power-up to ensure that the in and out
pointers of the FIFO are set to maximum separation.
FIFO_RST
PWRDN
LVTTL input
LVTTL input
Transmit FIFO Reset. When LOW, the in and out pointers of the transmit FIFO are set to
maximum separation. FIFO_RST must be activated at device power-up to ensure that the
in and out pointers of the FIFO are set to maximum separation. When the FIFO is being
reset, the output data is a 1010... pattern.
Device Power Down. When LOW, the logic and drivers are all disabled and placed into a
standby condition where only minimal power is dissipated.
Loop Control Signals
DIAGLOOP LVTTL input
Diagnostic Loopback Control. When HIGH, transmit data is routed through the receive
clock and data recovery and presented at the RXD[15:0] outputs. When LOW, received
serial data is routed through the receive clock and data recovery and presented at the
RXD[15:0] outputs.
Note:
3.
VREF equals to (VCC – 1.33)V if interfacing to a parallel LVPECL interface.
Document #: 38-02009 Rev. *J
Page 4 of 15
5秒后页面跳转
NTC热敏电阻与PTC热敏电阻的应用原理及应用范围
GTO与普通晶闸管相比为什么可以自关断？为什么普通晶闸管不能呢？从GTO原理、应用范围带你了解原因及推荐型号
LF353数据手册解读：特性、应用、封装、引脚说明、电气参数及替换型号推荐
A4950资料手册解读：特性、应用、封装、引脚功能、电气参数及代换型号
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
