5秒后页面跳转
捷配首页

Datasheet > BQ2011SN-D118
BQ2011SN-D118 PDF预览

BQ2011SN-D118

更新时间： 2024-10-28 02:55:07
品牌 Logo 应用领域
德州仪器 - TI 仪表
页数 文件大小 规格书
21页 195K
描述
Gas Gauge IC for High Discharge Rates

阅读下载

中文翻译

获取价格

BQ2011SN-D118 技术参数

是否无铅： 不含铅是否Rohs认证： 符合
生命周期：Active零件包装代码：SOIC
包装说明：SOP,针数：16
Reach Compliance Code：compliantECCN代码：EAR99
HTS代码：8542.39.00.01Factory Lead Time：1 week
风险等级：5.1可调阈值：NO
模拟集成电路 - 其他类型：POWER SUPPLY SUPPORT CIRCUITJESD-30 代码：R-PDSO-G16
JESD-609代码：e4长度：9.9 mm
湿度敏感等级：2信道数量：1
功能数量：1端子数量：16
最高工作温度：70 °C最低工作温度：
封装主体材料：PLASTIC/EPOXY封装代码：SOP
封装形状：RECTANGULAR封装形式：SMALL OUTLINE
峰值回流温度（摄氏度）：260认证状态：Not Qualified
座面最大高度：1.75 mm最大供电电压 (Vsup)：6.5 V
最小供电电压 (Vsup)：3 V标称供电电压 (Vsup)：4.25 V
表面贴装：YES温度等级：COMMERCIAL
端子面层：Nickel/Palladium/Gold (Ni/Pd/Au)端子形式：GULL WING
端子节距：1.27 mm端子位置：DUAL
处于峰值回流温度下的最长时间：NOT SPECIFIED宽度：3.9 mm
Base Number Matches：1

BQ2011SN-D118 数据手册

 浏览型号BQ2011SN-D118的Datasheet PDF文件第2页浏览型号BQ2011SN-D118的Datasheet PDF文件第3页浏览型号BQ2011SN-D118的Datasheet PDF文件第4页浏览型号BQ2011SN-D118的Datasheet PDF文件第5页浏览型号BQ2011SN-D118的Datasheet PDF文件第6页浏览型号BQ2011SN-D118的Datasheet PDF文件第7页 
bq2011  
Gas Gauge IC for  
High Discharge Rates  
Nominal available charge may be di-  
Features  
➤ Conservative and repeatable  
measurement of available charge  
in rechargeable batteries  
General Description  
rectly indicated using a five-seg-  
ment LED display. These segments  
are used to indicate graphically the  
nominal available charge.  
The bq2011 Gas Gauge IC is intended  
for battery-pack installation to main-  
tain an accurate record of available  
battery charge. The IC monitors a  
voltage drop across a sense resistor  
connected in series between the nega-  
tive battery terminal and ground to  
determine charge and discharge ac-  
tivity of the battery. The bq2011 is  
designed for systems such as power  
tools with very high discharge rates.  
➤ Designed for portable equipment  
such as power tools with high dis-  
charge rates  
The bq2011 supports a simple single-  
line bidirectional serial link to an exter-  
nal processor (common ground). The  
bq2011 outputs battery information in  
response to external commands over the  
serial link. To support subassembly  
testing, the outputs may also be con-  
trolled by command. The external proc-  
essor may also overwrite some of the  
bq2011 gas gauge data registers.  
➤ Designed for battery pack inte-  
gration  
- 120µA typical standby current  
(self-discharge estimation mode)  
Battery self-discharge is estimated  
based on an internal timer and tem-  
perature sensor. Compensations for  
battery temperature and rate of  
charge or discharge are applied to  
the charge, discharge, and  
selfdischarge calculations to provide  
available charge information across  
a wide range of operating conditions.  
Initial battery capacity is set using  
the PFC and MODE pins. Actual  
battery capacity is automatically  
“learned” in the course of a dis-  
charge cycle from full to empty and  
may be displayed depending on the  
display mode.  
- Small size enables imple-  
1
The bq2011 may operate directly  
from four cells. With the REF output  
and an external transistor, a simple,  
inexpensive regulator can be built to  
provide VCC from a greater number  
of cells.  
mentations in as little as  
square inch of PCB  
2
➤ Direct drive of LEDs for capacity  
display  
➤ Self-discharge compensation us-  
ing internal temperature sensor  
Internal registers include available  
charge, temperature, capacity, battery  
ID, and battery status.  
➤ Simple single-wire serial commu-  
nications port for subassembly  
testing  
➤ 16-pin narrow SOIC  
Pin Connections  
Pin Names  
MODE  
SEG1  
SEG2  
SEG3  
SEG4  
SEG5  
PFC  
Display mode output  
LED segment 1  
LED segment 2  
LED segment 3  
LED segment 4  
LED segment 5  
NC  
DQ  
No connect  
MODE  
1
2
3
4
5
6
16  
15  
14  
13  
12  
11  
V
CC  
Serial communications  
input/output  
SEG  
SEG  
SEG  
SEG  
SEG  
REF  
NC  
DQ  
RBI  
SB  
1
2
3
4
5
RBI  
SB  
Register backup input  
Battery sense input  
Display control input  
Sense resistor input  
3.0–6.5V  
DISP  
SR  
Programmed full count  
selection input  
PFC  
7
8
10  
9
DISP  
SR  
VCC  
VSS  
V
SS  
REF  
Voltage reference output  
Negative battery terminal  
16-Pin Narrow SOIC  
PN201101.eps  
2/96 E  
1
1234567...21

中文翻译

下载PDF

与BQ2011SN-D118相关器件

型号 品牌 获取价格 描述 数据表
BQ2011SN-D118G4 TI

获取价格

 		Gas Gauge IC for High Discharge Rates
BQ2011SN-D118TR TI

获取价格

 		Gas Gauge IC for High Discharge Rates
BQ2011SN-N TI

获取价格

 		Gas Gauge IC for High Discharge Rates
BQ2012 TI

获取价格

 		Gas Gauge IC With Slow-Charge Control
BQ2012PN ETC

获取价格

 		Battery Management
BQ2012PN-N ETC

获取价格

 		Battery Management
BQ2012SN TI

获取价格

 		Gas Gauge IC With Slow-Charge Control
BQ2012SN-D107 TI

获取价格

 		具有单总线 (DQ) 接口、5 个 LED 驱动器和慢充控制的镍镉电池/镍氢电池电量监测计
BQ2012SN-D107TR TI

获取价格

 		具有单总线 (DQ) 接口、5 个 LED 驱动器和慢充控制的镍镉电池/镍氢电池电量监测计
BQ2012SND107TRG4 TI

获取价格

 		1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16, GREEN, PLASTIC, MS-012 AC, SOIC-16

与BQ2011SN-D118相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证