5秒后页面跳转
捷配首页

Datasheet > AS29LV016BRG-100/XT
AS29LV016BRG-100/XT PDF预览

AS29LV016BRG-100/XT

更新时间： 2024-01-03 05:47:21
品牌 Logo 应用领域
AUSTIN 闪存内存集成电路光电二极管
页数 文件大小 规格书
40页 402K
描述
16 Megabit (2M x 8-Bit / 1M x 16-Bit) CMOS 3.0 Volt-Only Boot Sector Flash Memory

阅读下载

中文翻译

获取价格

AS29LV016BRG-100/XT 技术参数

是否Rohs认证： 不符合生命周期：Obsolete
零件包装代码：TSOP1包装说明：TSOP1-48
针数：48Reach Compliance Code：compliant
ECCN代码：3A001.A.2.CHTS代码：8542.32.00.51
风险等级：5.25Is Samacsys：N
最长访问时间：100 ns其他特性：BOTTOM BOOT BLOCK
备用内存宽度：8启动块：BOTTOM
命令用户界面：YES通用闪存接口：YES
数据轮询：YESJESD-30 代码：R-PDSO-G48
JESD-609代码：e4长度：18.4 mm
内存密度：16777216 bit内存集成电路类型：FLASH
内存宽度：16功能数量：1
部门数/规模：1,2,1,31端子数量：48
字数：1048576 words字数代码：1000000
工作模式：ASYNCHRONOUS最高工作温度：125 °C
最低工作温度：-55 °C组织：1MX16
封装主体材料：PLASTIC/EPOXY封装代码：TSOP1
封装等效代码：TSSOP48,.8,20封装形状：RECTANGULAR
封装形式：SMALL OUTLINE, THIN PROFILE并行/串行：PARALLEL
电源：3/3.3 V编程电压：3 V
认证状态：Not Qualified就绪/忙碌：YES
座面最大高度：1.2 mm部门规模：16K,8K,32K,64K
最大待机电流：0.000005 A子类别：Flash Memories
最大压摆率：0.035 mA最大供电电压 (Vsup)：3.6 V
最小供电电压 (Vsup)：2.7 V标称供电电压 (Vsup)：3 V
表面贴装：YES技术：CMOS
温度等级：MILITARY端子面层：PALLADIUM GOLD
端子形式：GULL WING端子节距：0.5 mm
端子位置：DUAL切换位：YES
类型：NOR TYPE宽度：12 mm
Base Number Matches：1

AS29LV016BRG-100/XT 数据手册

 浏览型号AS29LV016BRG-100/XT的Datasheet PDF文件第5页浏览型号AS29LV016BRG-100/XT的Datasheet PDF文件第6页浏览型号AS29LV016BRG-100/XT的Datasheet PDF文件第7页浏览型号AS29LV016BRG-100/XT的Datasheet PDF文件第9页浏览型号AS29LV016BRG-100/XT的Datasheet PDF文件第10页浏览型号AS29LV016BRG-100/XT的Datasheet PDF文件第11页 
COTS PEM  
BOOT SECTOR FLASH  
Austin Semiconductor, Inc.  
AS29LV016  
STANDBY MODE  
RESET#: HARDWARE RESET PIN  
When the system is not reading or writing to the device,  
it can place the device in the standby mode. In this mode,  
current consumption is greatly reduced, and the outputs  
are placed in the high impedance state, independent of  
the OE# input.  
The RESET# pin provides a hardware method of resetting  
the device to reading array data. When the system drives  
the RESET# pin to VIL for at least a period of tRP, the  
device immediately terminates any operation in  
progress, tristates all data output pins, and ignores all  
read/write attempts for the duration of the RESET# pulse.  
The device also resets the internal state machine to  
reading array data. The operation that was interrupted  
should be reinitiated once the device is ready to accept  
another command sequence, to ensure data integrity.  
The device enters the CMOS standby mode when the  
CE# and RESET# pins are both held at VCC 0.3 V.  
(Note that this is a more restricted voltage range than  
VIH.) If CE# and RESET# are held at VIH, but not within  
VCC 0.3 V, the device will be in the standby mode, but  
the standby current will be greater. The device requires  
standard access time (tCE) for read access when the device  
is in either of these standby modes, before it is ready to  
read data.  
Current is reduced for the duration of the RESET# pulse.  
When RESET# is held at VSS 0.3 V, the device draws  
CMOS standby current (ICC4). If RESET# is held at VIL but  
not within VSS 0.3 V, the standby current will be greater.  
If the device is deselected during erasure or programming,  
the device draws active current until the operation is  
completed.  
The RESET# pin may be tied to the system reset circuitry.  
Asystem reset would thus also reset the Flash memory,  
enabling the system to read the boot-up firmware from  
the Flash memory.  
ICC3 and ICC4 represents the standby current specification  
shown in the table in DC Characteristics on page 27.  
If RESET# is asserted during a program or erase  
operation, the RY/BY# pin remains a 0 (busy) until the  
internal reset operation is complete, which requires a time  
of tREADY (during EmbeddedAlgorithms). The system can  
thus monitor RY/BY# to determine whether the reset  
operation is complete. If RESET# is asserted when a  
program or erase operation is not executing (RY/BY# pin  
is 1), the reset operation is completed within a time of  
tREADY (not during EmbeddedAlgorithms). The system can  
read data tRH after the RESET# pin returns to VIH.Refer to  
the tables inAC Characteristics on page 29 for RESET#  
parameters and to Figure 13, on page 30 for the timing  
diagram.  
AUTOMATIC SLEEP MODE  
The automatic sleep mode minimizes Flash device energy  
consumption. The device automatically enables this mode  
when addresses remain stable for tACC + 30 ns. The  
automatic sleep mode is independent of the CE#, WE#,  
and OE# control signals. Standard address access timings  
provide new data when addresses are changed. While in  
sleep mode, output data is latched and always available  
to the system. ICC4 in the DC Characteristics on page 27  
represents the automatic sleep mode current specification.  
Austin Semiconductor, Inc. reserves the right to change products or specifications without notice.  
AS29LV016  
Rev. 2.1 10/08  
8
1...567891011...40

中文翻译

下载PDF

与AS29LV016BRG-100/XT相关器件

型号 品牌 获取价格 描述 数据表
AS29LV016BRG-70/ET AUSTIN

获取价格

 		16 Megabit (2M x 8-Bit / 1M x 16-Bit) CMOS 3.0 Volt-Only Boot Sector Flash Memory
AS29LV016BRG-70/ET MICROSS

获取价格

 		Flash, 1MX16, 70ns, PDSO48, TSOP1-48
AS29LV016BRG-90/ET MICROSS

获取价格

 		Flash, 1MX16, 90ns, PDSO48, TSOP1-48
AS29LV016BRG-90/ET AUSTIN

获取价格

 		16 Megabit (2M x 8-Bit / 1M x 16-Bit) CMOS 3.0 Volt-Only Boot Sector Flash Memory
AS29LV016BRG-90/XT AUSTIN

获取价格

 		16 Megabit (2M x 8-Bit / 1M x 16-Bit) CMOS 3.0 Volt-Only Boot Sector Flash Memory
AS29LV016BRG-90/XT MICROSS

获取价格

 		Flash, 1MX16, 90ns, PDSO48, TSOP1-48
AS29LV016J AUSTIN

获取价格

 		16 Megabit (2M x 8-Bit / 1M x 16-Bit) CMOS 3.0 Volt-Only Boot Sector Flash Memory
AS29LV016JBRG-55/ET AUSTIN

获取价格

 		16 Megabit (2M x 8-Bit / 1M x 16-Bit) CMOS 3.0 Volt-Only Boot Sector Flash Memory
AS29LV016JBRG-55/IT AUSTIN

获取价格

 		16 Megabit (2M x 8-Bit / 1M x 16-Bit) CMOS 3.0 Volt-Only Boot Sector Flash Memory
AS29LV016JBRG-55/XT AUSTIN

获取价格

 		16 Megabit (2M x 8-Bit / 1M x 16-Bit) CMOS 3.0 Volt-Only Boot Sector Flash Memory

与AS29LV016BRG-100/XT相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证