Freescale Semiconductor
Data Sheet: Advanced Information
Document Number: MCF51JE256
Rev. 4, 08/2012
An Energy-Efficient Solution from Freescale
MCF51JE256/128
MCF51JE256/128
The MCF51JE256 series devices are members of the low-cost,
low-power, high-performance ColdFire V1 family of 32-bit
microcontrollers (MCUs).
Not all features are available in all devices or packages; see
Table 1 for a comparison of features by device.
80-LQFP
12mm x 12mm
100-LQFP
14mm x 14mm
81-BGA
10mm x 10mm
104-BGA
10mm x 10mm
Peripherals
32-Bit ColdFire V1 Central Processor Unit (CPU)
•
USB — Dual-role USB On-The-Go (OTG) device, supports USB in either
•
Up to 50.33 MHz ColdFire CPU above 2.4 V and 40 MHz CPU above 2.1 V
and 20 MHz CPU above 1.8 V across temperature range of -40°C to
105°C.
ColdFire Instruction Set Revision C (ISA_C).
32-bit multiply and accumulate (MAC) supports signed or unsigned integer
or signed fractional inputs.
device, host or OTG configuration. On-chip transceiver and 3.3V regulator
help save system cost, fully compliant with USB Specification 2.0. Allows
control, bulk, interrupt and isochronous transfers.
•
•
•
•
•
•
•
•
•
SCIx — Two serial communications interfaces with optional 13-bit break;
option to connect Rx input to PRACMP output on SCI1 and SCI2; High
current drive on Tx on SCI1 and SCI2; wake-up from stop3 on Rx edge.
SPI1 — Serial peripheral interface with 32-bit FIFO buffer; 16-bit or 8-bit
data transfers; full-duplex or single-wire bidirectional; double-buffered
transmit and receive; master or slave mode; MSB-first or LSB-first shifting.
SPI2 — Serial peripheral interface with full-duplex or single-wire
bidirectional; Double-buffered transmit and receive; Master or Slave
mode; MSB-first or LSB-first shifting.
IIC — Up to 100 kbps with maximum bus loading; Multi-master operation;
Programmable slave address; Interrupt driven byte-by-byte data transfer;
supports broadcast mode and 10-bit addressing.
CMT — Carrier Modulator timer for remote control communications.
Carrier generator, modulator and driver for dedicated infrared out (IRO).
Can be used as an output compare timer.
TPMx — Two 4-channel Timer/PWM Module; Selectable input capture,
output compare, or buffered edge- or center-aligned PWM on each
channel; external clock input/pulse accumulator.
Mini-FlexBus — Multi-function external bus interface with user
programmable chip selects and the option to multiplex address and data
lines.
On-Chip Memory
•
256 K Flash comprised of two independent 128 K flash arrays;
read/program/erase over full operating voltage and temperature; allows
interrupt processing while programming.
32 KB System Random-access memory (RAM).
Security circuitry to prevent unauthorized access to RAM and Flash
contents.
•
•
Power-Saving Modes
•
•
•
Two ultra-low power stop modes. Peripheral clock enable register can
disable clocks to unused modules to reduce currents.
Time of Day (TOD) — Ultra low-power 1/4 sec counter with up to 64 sec
timeout.
Ultra-low power external oscillator that can be used in stop modes to
provide accurate clock source to the TOD. 6 µs typical wake up time from
stop3 mode.
Clock Source Options
•
•
•
Oscillator (XOSC1) — Loop-control Pierce oscillator; 32.768 kHz crystal or
ceramic resonator dedicated for TOD operation.
•
•
PRACMP — Analog comparator with selectable interrupt; compare option
to programmable internal reference voltage; operation in stop3.
ADC12 — 12-bit Successive approximation ADC with up to12
Oscillator (XOSC2) for high frequency crystal input for MCG reference to
be used for system clock and USB operations.
Multipurpose Clock Generator (MCG) — PLL and FLL; precision trimming
of internal reference allows 0.2% resolution and typical +0.5% to -1%
deviation over temperature and voltage; supports CPU frequencies up to
50 MHz.
single-ended channels; internal bandgap reference channel; operation in
stop3; fully functional from 3.6V to 1.8V.
•
PDB — Programmable delay block with 16-bit counter and modulus and
prescale to set reference clock to bus divided by 1 to bus divided by 2048;
8 trigger outputs for ADC module provides periodic coordination of ADC
sampling sequence with sequence completion interrupt; Back-to-Back
mode and Timed mode.
System Protection
•
Watchdog computer operating properly (COP) reset with option to run from
dedicated 1 kHz internal clock source or bus clock.
•
Low-voltage detection with reset or interrupt; selectable trip points;
separate low voltage warning with optional interrupt; selectable trip points.
Illegal opcode and illegal address detection with reset.
Flash block protection for each array to prevent accidental write/erasure.
Hardware CRC to support fast cyclic redundancy checks.
•
DAC — 12-bit resolution DAC; configurable settling time.
Input/Output
•
•
•
•
•
•
Up to 68 GPIOs and 1 output-only pin.
Voltage Reference output (VREFO).
Dedicated infrared output pin (IRO)
withhigh current sink capability.
Up to 16 KBI pins with selectable
polarity.
Development Support
•
Integrated ColdFire DEBUG_Rev_B+ interface with single wire BDM
•
•
connection supports same electrical interface used by the S08 family
debug modules.
Up to 16 pins of rapid general purpose
I/O (RGPIO).
•
•
Real-time debug with 6 hardware breakpoints (4 PC, 1 address and 1
data).
On-chip trace buffer provides programmable start/stop recording
conditions.
This document contains information on a product under development. Freescale reserves the
right to change or discontinue this product without notice.
© Freescale Semiconductor, Inc., 2009-2012. All rights reserved.
5秒后页面跳转
摩尔斯微电子在美国约书亚树国家公园测试 Wi-Fi HaLow
贸泽上架Tallysman TW5386智能GNSS天线
SL74HC10N：高性能三输入与非门解析
AIC1781A 电池充电控制器深度解析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
