Datasheet > 224472-1

224472-1

更新时间： 2024-09-14 01:04:23

品牌	Logo	应用领域
MACOM		/
页数	文件大小	规格书
5页	136K
描述
Installation and removal of the crimper from the tool holder assembly

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

224472-1 数据手册

Instruction Sheet

“T”-HEAD* Crimper 217202-1

(Used with 626 Pneumatic Tooling Systems)

408-4214

12 MAR 10 Rev A

Tool Holder

Assembly

189928-1

(Ref)

“T”-HEAD Crimper

217202-1

Quick Pins

(Ref)

Figure 1

1. INTRODUCTION

2. DESCRIPTION (Figure 1)

The “T”--HEAD Crimper attaches (via four quick pins)

to the tool holder assembly of the pneumatic power

unit. When actuated, a cam extends through the tool

holder into the crimper, driving an internal, roller--

guided envelope. The other end of this mechanism is

connected to an anvil and, as the cam pushes against

the roller--guided envelope, the anvil moves in a

straight line and bottoms against a stationary

“T”--HEAD Crimper 217202--1 is designed to crimp

PIDG* and PLASTI--GRIP* terminals on wire sizes

22--14 AWG. The crimper is used with 626 Pneumatic

Tooling Assemblies 189721--1, 189722--1, 189723--1,

and 189724--1. For information concerning the setup

and operation of the pneumatic tools, refer to

Customer Manual 409--5862.

This instruction sheet provides:

indenter. When the cam of the pneumatic tool

retracts, the force is removed from the envelope.

S Installation and removal of the crimper from the

tool holder assembly.

The envelope must then be manually retracted by use

of a plastic slide switch. The plastic slide switch

permits opening and closing of the anvil for insertion

and removal of terminals or splices.

S Maintenance, inspection, and repair information

for the crimper.

For information concerning wire preparation, crimping

procedures, and crimp inspection, refer to the

associated instructions supplied with the terminals.

3. INSTALLATION AND REMOVAL OF CRIMPER (Figure 1)

Read these instructions thoroughly before

proceeding.

Before installing the crimper, refer to Customer

Manual 409--5862 for instructions on installing the

appropriate tool holder assembly (including cam) on

the pneumatic tool. After the appropriate tool holder

assembly has been installed, proceed as follows:

Measurements are in metric units [followed by

U.S. customary units in brackets]. Figures and

illustrations are not drawn to scale and are for

reference only.

NOTE

Removal is the reverse of installation.

NOTE

TOOLING ASSISTANCE CENTER 1-800-722-1111

PRODUCT INFORMATION 1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.tycoelectronics.com

E2010 Tyco Electronics Corporation, Berwyn, PA

1 of 5

TE logo and Tyco Electronics are trademarks.

LOC B

*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.

12 3 4 5

中文翻译

下载PDF

与224472-1相关器件

型号	品牌	获取价格	描述	数据表
224473-1	MACOM	获取价格	Installation and removal of the crimper from the tool holder assembly
224474-1	MACOM	获取价格	Installation and removal of the crimper from the tool holder assembly
224475-1	MACOM	获取价格	Installation and removal of the crimper from the tool holder assembly
224-4844-00-3303	ETC	获取价格	SOCKEL IC MIT SCHRAUBBETAETIGUNG 24POL
2245	KR	获取价格	Bandpass Filter
224500	LITTELFUSE	获取价格	2AG Fast-Acting Fuse
22450C	ETC	获取价格	Manual ?lanSC520 Microcontroller Customer Dev
224-5248-00-0602J	3M	获取价格	DIP24, IC SOCKET
224-5248-19-0602J	3M	获取价格	DIP24, IC SOCKET
22-45-5023	MOLEX	获取价格	Board Connector, 2 Contact(s), 1 Row(s), Female, Straight, IDC Terminal, ROHS COMPLIANT

与224472-1相关文章

SL74HC10N：高性能三输入与非门解析
2024-09-03

78
AIC1781A 电池充电控制器深度解析
2024-09-03

69
Pickering新高压舌簧继电器亮相汽车测试博览会
2024-08-26

99
采用MCU+MPU双处理器架构实现的创新应用设计探索
2024-08-23

113

产品中心

服务支持

精选活动

关于我们

帮助中心

224472-1

224472-1 数据手册

与224472-1相关器件

与224472-1相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

224472-1

224472-1 数据手册

与224472-1相关器件

与224472-1相关文章

您还可以找

您在本页遇到什么问题？