5秒后页面跳转
1213564--1 PDF预览

1213564--1

更新时间: 2024-11-08 01:14:47
品牌 Logo 应用领域
MACOM /
页数 文件大小 规格书
5页 112K
描述
Double Action Hand Tool

1213564--1 数据手册

 浏览型号1213564--1的Datasheet PDF文件第2页浏览型号1213564--1的Datasheet PDF文件第3页浏览型号1213564--1的Datasheet PDF文件第4页浏览型号1213564--1的Datasheet PDF文件第5页 
Instruction Sheet  
Double Action Hand Tool (DAHT)  
Adapter Assembly 1213563-1  
408-4485  
17 MAR 10 Rev B  
(For Use With 626 Pneumatic Tooling Assemblies)  
Setscrew  
Typical DAHT  
Crimp Head (Ref)  
Mounting Holes  
Clevis  
Adapter Cavity  
Adapter  
Cam  
Adapter Assembly  
Quick Pins  
(Supplied with  
Adapter Assembly)  
Clevis  
Figure 1  
Read these instructions thoroughly before  
proceeding.  
1. INTRODUCTION  
DAHT Adapter Assembly 1213563--1 is designed to  
accept the crimp head from any DAHT to adapt the  
crimp head for use with 626 pneumatic tooling  
assemblies. DAHTs are available from Tyco  
Electronics. For information concerning the setup and  
operation of the pneumatic tool, refer to Customer  
Manual 409--5862.  
Dimensions are in millimeters [with inch  
equivalents in brackets]. Figures and illustrations  
are for identification only and are not drawn to  
scale.  
NOTE  
i
Reasons for reissue of this instruction sheet are  
provided in Section 6, REVISION SUMMARY.  
This instruction sheet provides:  
2. DESCRIPTION  
— recommended procedures for crimp head  
removal from the hand tool  
The adapter assembly facilitates the connection of the  
crimp head (typical shown in Figure 1) to the  
— crimp head installation into the adapter  
pneumatic tool and provides the necessary motion of  
the crimp head jaws when the pneumatic tool is  
actuated. When the tool is actuated, the cam extends  
into the adapter, contacting the crimp head jaws.  
When the cam retracts, the force is removed from the  
jaws and they return to their starting position.  
— installation and removal of the cam and adapter  
from the pneumatic tool  
— maintenance, inspection, and repair information  
for the adapter  
The jaws may be opened and closed manually by  
simultaneously squeezing the two opposing clevises,  
which are coupled to the jaws. The quick pins secure  
the crimp head to the adapter.  
For wire preparation and crimping procedure, and  
crimp head maintenance, inspection, and repair, refer  
to the associated instruction sheet.  
TOOLING ASSISTANCE CENTER 1-800-722-1111  
PRODUCT INFORMATION 1-800-522-6752  
This controlled document is subject to change.  
For latest revision and Regional Customer Service,  
visit our website at www.tycoelectronics.com  
E2010 Tyco Electronics Corporation, Berwyn, PA  
1 of 5  
All Rights Reserved  
TE logo and Tyco Electronics are trademarks.  
LOC B  
*Trademark. Other products names, logos, or company names might be trademarks of their respective owners.  

与1213564--1相关器件

型号 品牌 获取价格 描述 数据表
1213565--1 MACOM

获取价格

Double Action Hand Tool
1213566--1 MACOM

获取价格

Double Action Hand Tool
1213667-1 TE

获取价格

Seating Tool Assembly
1213668-1 TE

获取价格

Seating Tool Assembly
1213669-1 TE

获取价格

Seating Tool Assembly
12136AF HITACHI

获取价格

Dolby B-Type Noise Reduction System
121-37-9 WINCHESTER

获取价格

RF TNC Connector, Female, Panel Mount, Cable Mount, Crimp Terminal, Jack
121-38.4K-12.5-20R OSCILENT

获取价格

Parallel - Fundamental Quartz Crystal, 0.0384MHz Nom,
1213801 SICK

获取价格

MEASURING AUTOMATION LIGHT GRIDS
1-213826-0 TE

获取价格

RECEPTACLE ASSEMBLY, POSTED, REVERSE SEX, SERIES 1, 17-9, CPC