Datasheet > 1213859-1

1213859-1

更新时间： 2024-11-08 00:59:35

品牌	Logo	应用领域
MACOM		/
页数	文件大小	规格书
5页	530K
描述
The CERTI--CRIMP II Tool Holder Assembly

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

1213859-1 数据手册

Instruction Sheet

CERTI-CRIMP* II Tool Holder Assembly

1213860-1 (for Use with the SDE Electric

Bench Terminator)

408-10021

16 MAR 10 Rev C

Crimping Head

CERTI -CRIMP II Tool

Holder Assembly

1213860-1 (for use

with the SDE Electric

Bench Terminator)

SDE Electric

Bench Terminator

Figure 1

For information concerning the setup and operation of

the SDE Electric Bench Terminator, refer to customer

manual 409--10052.

1. INTRODUCTION

The CERTI--CRIMP II Tool Holder Assembly

1213860--1 is used to adapt the crimping head from a

CERTI--CRIMP II Hand Tool to an SDE Electric

Bench Terminator. Figure 1 shows a typical crimping

head, mounted to CERTI--CRIMP II Tool Holder

Assembly 1213860--1, installed onto an SDE Electric

Bench Terminator.

Read this instruction sheet, and the related customer

manual, thoroughly before using the tool holder

assembly.

2. DESCRIPTION

The tool holder assembly facilitates the connection of

the crimping head to the SDE Electric Bench Machine

and provides the necessary straight line motion of the

movable die when the SDE Electric Bench Machine is

actuated.

Figures and illustrations are for reference only,

and are not to scale.

NOTE

This instruction sheet provides:

The tool holder assembly features a switch (handle)

and three quick pins. See Figure 2. The switch

(handle) can be used to manually open and close the

dies of the crimping head for insertion and removal of

the product.

S Instructions for installing and removing the tool

holder assembly to the Electric Bench Machine

S Instructions for installing the crimping head

onto the tool holder assembly

The two outer quick--release pins secure the outer

tabs of the crimping head to the tool holder assembly,

and the center quick--release pin secures the the

movable die of the crimping head to the internal

spring--loaded switch of the tool holder assembly.

S Instructions for adjusting the crimp height

S Maintenance, inspection, and repair

instructions for the tool holder assembly

TOOLING ASSISTANCE CENTER 1-800-722-1111

PRODUCT INFORMATION 1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.tycoelectronics.com

E2010 Tyco Electronics Corporation, Berwyn, PA

1 of 5

TE logo and Tyco Electronics are trademarks.

LOC B

*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.

12 3 4 5

中文翻译

下载PDF

与1213859-1相关器件

型号	品牌	获取价格	描述	数据表
1213861-1	MACOM	获取价格	The CERTI--CRIMP II Tool Holder Assembly
1213862-1	TE	获取价格	ANVIL, WIRE
1213880-1	TE	获取价格	CRIMPER, INSULATION
1213881-1	TE	获取价格	ANVIL, WIRE
1213882-1	TE	获取价格	ANVIL, INSULATION
1213908	SICK	获取价格	MEASURING AUTOMATION LIGHT GRIDS
1213909	SICK	获取价格	MEASURING AUTOMATION LIGHT GRIDS
1213909-3	TE	获取价格	CRIMPER, WIRE
1213A204-402	WINCHESTER	获取价格	RF MCX Connector
1213A204-405	WINCHESTER	获取价格	RF MCX Connector