VLED-150W-HV Series
347-480V Input, Fixed & Dimmable Output
Switch Mode LED Drivers
Constant Current with Isolation
Aluminum Housing
Electrical Specifications
Input Voltage Range:
347-480 Nom. Vac (312-512 V Min/Max)
Frequency:
50/60 Hz Nom. (47-63 Hz Min/Max)
>0.90 @ 75-100% load, 347-480V
Power Factor:
Inrush Current:
Input Current:
Maximum Power:
Line Regulation:
Load Regulation:
THD:
20 Amps max @ 480Vac, cold start 25ºC
0.70A max @ 347Vac, 0.42A max @ 480Vac
150W
± 1%
± 3%
<_ 20% @ 75-100% load, 347-480V
1 mA @ 480VAC, 60Hz
89-91% at 347VAC
1S max
Leakage Current:
Typical Efficiency
Turn-on Delay:
Protection:
• Total Power: 150 Watts
• Input Voltage: 347-480 Vac Nom.
• UL Dry & Damp Location Rated
• IP67
Over-Voltage, Over-Temperature (105°C),
and Short Circuit Protection
• High Power Factor
• UL8750, EN61347
Environmental Specifications
Minimum Starting Temp: -40ºC
Storage Temperature:
Humidity:
-40ºC to +85ºC
5% to 100%
Convection
Class A
Cooling:
Sound Rating:
MTBF:
250,000 Hours @ 480VAC input, 80% load and 25ºC
ambient conditions per MIL-HDBK-217F
Lifetime:
Weight:
145,700 Hours @ 480Vac, 80% load and 45ºC ambient
2.87 lbs. (1300g)
Ordering Options:
Constant Current - Product Specifications
-D:
0-10V dimmable version comes with an extra three wires Purple/Gray/Blk-Wht on the
output side. Dimming is compatible with most quality 0-10V wall dimmers and direct
0-10V analog signal. See page 3 for additional specifications.
Output Current Output Voltage Max. Output Typical
Model Number
(mA ±5%)
Range (Vdc)
129-258
107-214
71-142
53-107
36-71
Power (W) Efficiency
VLED150W-258-C0580-
VLED150W-214-C0700-
VLED150W-142-C1050-
VLED150W-107-C1400-
VLED150W-071-C2100-
VLED150W-054-C2800-
VLED150W-043-C3500-
VLED150W-036-C4200-
X-HV
X-HV
X-HV
X-HV
X-HV
X-HV
X-HV
X-HV
580
150
150
150
150
150
150
150
150
91%
91%
90%
90%
90%
90%
89%
89%
700
1050
1400
2100
2800
3500
4200
27-54
21-43
18-36
-X indicates dimming options are available. See options at left. Blank = fixed current output
E332160
Note:
LED drivers are designed and intended to operate LED loads only.
Non-LED loading may be outside the specified design limits of our
LED drivers, and therefore cannot be covered by any warranty.
If you desire to use our LED drivers to operate non-LED loads
please contact us to discuss compatibility.
Specifications subject to change without notice.
Rev 8-25-15
Thomas Research Products • 1225 Bowes Rd • Elgin, IL 60123 • T 847-515-3057 • F 847-515-3047 • www.trpssl.com