ALUMINUM ELECTROLYTIC CAPACITORS
6mmL Chip Type, Bi-Polarized
UP series
Chip type, bi-polarized withstanding high temperature range up to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
Extended
UN
range
U P
High
Temperature
WP
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
–55 ~ +105°C
6.3 ~ 50V
0.1 ~ 47µF
±20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.05 CV or 10 (µA), whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Rated voltage (V)
6.3
10
16
25
35
50
tan
δ
tan δ (MAX.)
0.24
0.20
0.17
0.17
0.15
0.15
Measurement frequency : 120Hz
Rated voltage (V)
6.3
4
8
10
3
6
16
2
4
25
2
4
35
2
3
50
2
3
Stability at Low Temperature
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
After 1000 hours' application of rated
Capacitance change
tan δ
Within ±20% of initial value
voltage at 105°C with the polarity inverted
every 250 hours, capacitors meet the
characteristic requirements listed at right.
Endurance
Shelf Life
200% or less of initial specified value
Initial specified value or less
Leakage current
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C
Capacitance change
tan δ
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
Resistance to soldering
heat
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Leakage current
Marking
Black print on the case top.
Type numbering system (Example : 16V 10 F)
µ
Chip Type
1
2
3
4
5
6
7
8
9 10 11 12 13 14
105°C Marking
U U P 1 C 1 0 0 M C L 1 G S
Plastic platform
Capacitance
0.3 MAX.
C±0.2
Voltage
Lot No.
Taping code
(mm)
6.3
Configuration
φD
4
5
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
A
B
C
E
L
1.8 2.1 2.4
4.3 5.3 6.6
4.3 5.3 6.6
1.0 1.3 2.2
5.8 5.8 5.8
L±0.3
0.5 ~ 0.8
Type
Voltage mark for 6.3V is 6V
Dimensions
6.3
10
16
25
35
50
V
Cap.(µF)
Code
0J
1A
1C
1E
1V
1H
0.1
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
4
1.0
2.0
2.8
4.0
8.4
0.22
0.33
0.47
1
4
4
4
4
2.2
3.3
4.7
4
8.4
16
5
13
5
12
16
27
5
5
17
20
4
12
5
5
18
29
6.3
10
4
17
33
41
5
23
37
49
6.3
6.3
22
33
47
5
28
6.3
6.3
6.3
6.3
6.3
6.3
37
45
Rated
ripple
Case size
φD (mm)
Rated Ripple (mArms) at 105°C 120Hz
Taping specifications are given in page 24.
Frequency coefficient of rated ripple current
Recommended land size, soldering by reflow are given in page 25, 26.
Please select UN(p.77) series if high CV products are required.
Please refer to page 3 for the minimum order quantity.
Frequency
50 Hz
120 Hz
300 Hz
1 kHz
10 kHz~
1.50
Coefficient
0.70
1.00
1.17
1.36
CAT.8100V