TPS2500, TPS2501
www.ti.com ................................................................................................................................................ SLVS886A–OCTOBER 2008–REVISED AUGUST 2009
INTEGRATED USB POWER SWITCH WITH BOOST CONVERTER
1
FEATURES
APPLICATIONS
•
•
Portable Applications Using Single Li+ Cell
USB Hosts Without Native 5-V Supplies
23
•
Integrated Synchronous Boost Converter and
USB Current-Limit Power Switch
•
Light-Load, High-Efficiency Eco-mode™
Control Scheme (TPS2500) or Constant
Frequency (TPS2501)
DESCRIPTION
The TPS2500 and TPS2501 provide an integrated
solution to meet USB 5-V power requirements from a
1.8-V to 5.25-V input supply. The features include a
Hi-Speed USB compliant power output, output switch
enable, current limit, and overcurrent fault reporting.
•
•
1.8-V to 5.25-V Input Voltage (2.2-V Minimum
Start-Up Voltage)
Adjustable USB Current Limit
–
130 mA to 1400 mA (Typical)
The 1.8-V to 5.25-V input can be supplied by sources
including dc/dc regulated supplies (e.g., 3.3 V), or
batteries such as single-cell Li+ or three-cell NiCd,
NiMH, or alkaline.
•
•
•
•
•
Accurate 20% Current Limit at 1.4-A Setting
Powers up to Two Standard USB Ports
Auxiliary 5.1-V Output
Minimal External Components Required
The USB power-switch current limit is programmable
via an external resistor from as low as 130 mA to as
high as 1400 mA (typical). Two standard USB ports
can be supported from a single TPS2500 or TPS2501
at the 1400-mA setting.
Fast Overcurrent-Response Time – 5 µs
Typical
•
•
Small 3-mm × 3-mm × 0.9-mm SON-10 Package
15-kV / 8-kV System-Level ESD Capable
Additionally, the boost converter output is available as
an auxiliary 5.1-V output to power additional loads.
The total current supplied by the USB output and the
auxiliary cannot exceed 1148 mA at VIN = 3 V.
TYPICAL APPLICATION CIRCUIT
2.2 mH
SW
IN
BOOST EFFICIENCY
vs
5 V Auxiliary Load
Power, 100 mA(2)
1.8-V to
5.25-V Input
AUX
EN
10 mF
22 mF
ENUSB
FAULT
OUTPUT AUXILIARY CURRENT
RFAULT
0.97
USB FAULT Flag
0.95
0.93
5 V USB Power
5 V USB
Port #1
500 mA
USB
ILIM
Data
V
IN
= 4.5 V
GND
RILIM
PGND
0.91
0.89
0.87
0.85
0.83
0.81
0.79
0.77
120 mF(1)
POWER PAD
V
IN
= 3.3 V
5 V USB
Port #2
500 mA
Data
S0380-02
(1) Requirement for USB applications only;
downstream facing ports should be
bypassed with 120 µF minimum per hub.
V
IN
= 1.8 V
(2) Additional current can be supplied from
AUX if <1 A is required for USB ports;
total current should not exceed 1.1 A at
VIN = 3 V.
0
300
600
900
1200
1500
I (AUX) − Output Auxiliary Current − mA
O
G001
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
3
Eco-mode, PowerPAD are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2009, Texas Instruments Incorporated