5秒后页面跳转
TPIC44L02DBG4 PDF预览

TPIC44L02DBG4

更新时间: 2024-11-30 01:08:31
品牌 Logo 应用领域
德州仪器 - TI 驱动光电二极管接口集成电路驱动器
页数 文件大小 规格书
24页 815K
描述
4-CHAMMEL SERIAL AND PARALLEL LOW-SIDE PRE-FET DRIVER

TPIC44L02DBG4 技术参数

是否无铅: 不含铅是否Rohs认证: 符合
生命周期:Active零件包装代码:SSOP
包装说明:SSOP, SSOP28,.3针数:24
Reach Compliance Code:compliantECCN代码:EAR99
HTS代码:8542.39.00.01Factory Lead Time:12 weeks
风险等级:5.21高边驱动器:NO
接口集成电路类型:BUFFER OR INVERTER BASED MOSFET DRIVERJESD-30 代码:R-PDSO-G24
JESD-609代码:e4长度:8.2 mm
湿度敏感等级:1功能数量:1
端子数量:24最高工作温度:125 °C
最低工作温度:-40 °C最大输出电流:0.0012 A
标称输出峰值电流:0.0012 A封装主体材料:PLASTIC/EPOXY
封装代码:SSOP封装等效代码:SSOP28,.3
封装形状:RECTANGULAR封装形式:SMALL OUTLINE, SHRINK PITCH
峰值回流温度(摄氏度):260电源:5 V
认证状态:Not Qualified座面最大高度:2 mm
子类别:MOSFET Drivers最大压摆率:4.2 mA
最大供电电压:5.5 V最小供电电压:4.5 V
标称供电电压:5 V电源电压1-最大:24 V
电源电压1-分钟:8 V电源电压1-Nom:12 V
表面贴装:YES温度等级:AUTOMOTIVE
端子面层:Nickel/Palladium/Gold (Ni/Pd/Au)端子形式:GULL WING
端子节距:0.65 mm端子位置:DUAL
处于峰值回流温度下的最长时间:NOT SPECIFIED断开时间:3.5 µs
接通时间:4 µs宽度:5.3 mm
Base Number Matches:1

TPIC44L02DBG4 数据手册

 浏览型号TPIC44L02DBG4的Datasheet PDF文件第2页浏览型号TPIC44L02DBG4的Datasheet PDF文件第3页浏览型号TPIC44L02DBG4的Datasheet PDF文件第4页浏览型号TPIC44L02DBG4的Datasheet PDF文件第5页浏览型号TPIC44L02DBG4的Datasheet PDF文件第6页浏览型号TPIC44L02DBG4的Datasheet PDF文件第7页 
ꢀ ꢁꢂ ꢃꢄ ꢄ ꢅꢆ ꢇ ꢈ ꢀ ꢁꢂ ꢃꢄ ꢄ ꢅꢆ ꢉ ꢈ ꢀ ꢁ ꢂꢃ ꢄꢄ ꢅꢆ ꢊ  
ꢄ ꢋꢃꢌ ꢍꢎꢎ ꢏꢅ ꢐꢏ ꢑꢂꢍ ꢅ ꢍꢎꢒ ꢁꢍꢑꢍ ꢅꢅ ꢏꢅ ꢅ ꢓ ꢔꢋꢐꢂ ꢒꢏ ꢁꢑꢏ ꢋꢕ ꢏꢀ ꢒ ꢑꢂ ꢖ ꢏꢑ  
SLIS062B NOVEMBER 1996 – REVISED AUGUST 2001  
D
4-Channel Serial-In Parallel-In Low-Side  
Pre-FET Driver  
D
Asynchronous Open-Drain Fault Flag  
D
D
D
D
D
Device Output Can Be Wire-ORed With  
Multiple Devices  
D
Devices Are Cascadable  
D
Internal 55-V Inductive Load Clamp and  
Fault Status Returned Through Serial  
Output Terminal  
V
FETs  
Protection Clamp for External Power  
GS  
Internal Global Power-On Reset of Device  
and External RESET Terminal  
D
Independent Shorted-Load/Short-to-  
Battery Fault Detection on All Drain  
Terminals  
High-Impedance CMOS-Compatible Inputs  
With Hysteresis  
D
D
D
Independent OFF-State Open-Load Fault  
Sense  
TPIC44L01 and TPIC44L03 Disables the  
Gate Output When a Shorted-Load Fault  
Occurs  
Over-Battery-Voltage Lockout Protection  
and Fault Reporting  
D
TPIC44L02 Transitions the Gate Output to a  
Low-Duty Cycle PWM Mode When a  
Shorted-Load Fault Occurs  
Under-Battery Voltage Lockout Protection  
for the TPIC44L01 and TPIC44L02  
description  
DB PACKAGE  
(TOP VIEW)  
The TPIC44L01, TPIC44L02, and TPIC44L03 are  
low-side predrivers that provide serial and parallel  
input interfaces to control four external FET power  
switches such as offered in the TI TPIC family of  
power arrays. These devices are designed  
primarily for low-frequency switching, inductive  
load applications such as solenoids and relays.  
Fault status for each channel is available in a  
serial-data format. Each driver channel has  
independent off-state open-load detection and  
on-state shorted-load/short-to-battery detection.  
Battery overvoltage and undervoltage detection  
and shutdown is provided on the TPIC44L01/L02.  
On the TPIC44L03 driver, only over-battery  
voltage shutdown is provided. Each channel also  
provides inductive-voltage-transient protection  
for the external FET.  
FLT  
VCOMPEN  
VCOMP  
IN0  
V
BAT  
N/C  
1
24  
23  
22  
21  
20  
19  
18  
17  
16  
15  
14  
2
RESET  
DRAIN0  
GATE0  
DRAIN1  
GATE1  
GATE2  
DRAIN2  
GATE3  
DRAIN3  
3
4
IN1  
5
IN2  
6
IN3  
7
CS  
8
SDO  
9
SDI  
10  
11  
12  
SCLK  
V
13 GND  
CC  
These devices provide control of output channels through a serial input interface or a parallel input interface.  
A command to enable the output from either interface enables the respective channels gate output to the  
external FET. The serial interface is recommended when the number of signals between the control device and  
the predriver must be minimized and the speed of operation is not critical. In applications where the predriver  
must respond very quickly or asynchronously, the parallel input interface is recommended.  
For serial operation, the control device must transition CS from high to low to activate the serial input interface.  
When this occurs, SDO is enabled, fault data is latched into the serial interface, and the fault flag is refreshed.  
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of  
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.  
Copyright 2001, Texas Instruments Incorporated  
ꢀꢣ  
ꢟ ꢣ ꢠ ꢟꢘ ꢙꢭ ꢛꢚ ꢞ ꢦꢦ ꢤꢞ ꢜ ꢞ ꢝ ꢣ ꢟ ꢣ ꢜ ꢠ ꢨ  
1
POST OFFICE BOX 655303 DALLAS, TEXAS 75265  

TPIC44L02DBG4 替代型号

型号 品牌 替代类型 描述 数据表
TPIC44L02DB TI

完全替代

4-CHANNEL SERIAL AND PARALLEL LOW-SIDE PRE-FET DRIVER

与TPIC44L02DBG4相关器件

型号 品牌 获取价格 描述 数据表
TPIC44L02DBR TI

获取价格

4-CHAMMEL SERIAL AND PARALLEL LOW-SIDE PRE-FET DRIVER
TPIC44L02DBRG4 TI

获取价格

4-CHAMMEL SERIAL AND PARALLEL LOW-SIDE PRE-FET DRIVER
TPIC44L03 TI

获取价格

4-CHANNEL SERIAL AND PARALLEL LOW-SIDE PRE-FET DRIVER
TPIC44L03DB TI

获取价格

4-CHANNEL SERIAL AND PARALLEL LOW-SIDE PRE-FET DRIVER
TPIC44L03DBR TI

获取价格

暂无描述
TPIC46L01 TI

获取价格

6-CHANNEL SERIAL AND PARALLEL LOW-SIDE PRE-FET DRIVER
TPIC46L01DB TI

获取价格

6-CHANNEL SERIAL AND PARALLEL LOW-SIDE PRE-FET DRIVER
TPIC46L01DBG4 TI

获取价格

6-CHANNEL SERIAL AND PARALLEL LOW-SIDE PRE-FET DRIVER
TPIC46L01DBLE TI

获取价格

6-CHANNEL SERIAL AND PARALLEL LOW-SIDE PRE-FET DRIVER
TPIC46L01DBR TI

获取价格

6-CHANNEL SERIAL AND PARALLEL LOW-SIDE PRE-FET DRIVER