TISP3070T3BJ THRU TISP3395T3BJ
DUAL BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS
TISP3xxxT3BJ Overvoltage Protector Series
Dual High Current Protectors in a Space Efficient
Package
SMB Package (Top View)
- 2 x 100 A 10/560 Current Rating
1
3
- Modified 3-pin SMB (DO-214AA) Package
50 % Space Saving over Two SMBs
- Y Configurations with Two SMB Packages
2 x 80 A, 10/1000 . . . .TISP3xxxT3BJ + TISP4xxxJ1BJ
2 x 100 A, 10/700 . . . .TISP3xxxT3BJ + TISP4xxxH3BJ
2
MDXXCJA
Device Symbol
Ion-Implanted Breakdown Region
- Precise and Stable Voltage
1
3
(T or R)
(T or R)
- Low Voltage Overshoot under Surge
VDRM
V(BO)
Device
V
V
TISP3070T3
TISP3080T3
TISP3095T3
TISP3115T3
TISP3125T3
TISP3145T3
TISP3165T3
TISP3180T3
TISP3200T3
TISP3219T3
TISP3250T3
TISP3290T3
TISP3350T3
TISP3395T3
58
70
65
80
75
95
SD3TAA
2
(G)
90
115
125
145
165
180
200
219
250
290
350
395
100
120
135
145
155
180
190
220
275
320
Rated for International Surge Wave Shapes
IPPSM
Wave Shape
Standard
A
2/10
8/20
GR-1089-CORE
IEC 61000-4-5
250
250
150
120
100
80
10/160
10/700
10/560
10/1000
TIA/EIA-IS-968 (FCC Part 68)
ITU-T K.20/.21/.45
TIA/EIA-IS-968 (FCC Part 68)
GR-1089-CORE
.......................................UL Recognized Component
Description
These dual bidirectional thyristor devices protect central office, access and customer premise equipment against overvoltages on the
telecom line. The TISP3xxxT3BJ is available in a wide range of voltages and has an 80 A 10/1000 current rating. These protectors have
been specified mindful of the following standards and recommendations: GR-1089-CORE, TIA/EIA-IS-968, UL 60950, EN 60950, IEC
60950, ITU-T K.20, K.21 and K.45. The TISP3350T3BJ meets the FCC Part 68 “B” ringer voltage requirement (VDRM = ±275 V). Housed
in a 3-pin modified SMB (DO-214AA) package, the TISP3xxxT3BJ range is space efficient solution for protection designs of 80 A or less
which use multiple SMBs.
These devices allow signal voltages, without clipping, up to the maximum off-state voltage value, VDRM, see Figure 1. Voltages above
V
DRM are limited and will not exceed the breakover voltage, V(BO), level. If sufficient current flows due to the overvoltage, the device
switches into a low-voltage on-state condition, which diverts the current from the overvoltage through the device. When the diverted cur-
rent falls below the holding current, IH, level the device switches off and restores normal system operation.
How To Order
For Standard
For Lead Free
Termination Finish Termination Finish
Device
Package
Carrier
Order As
Order As
TISP3xxxT3BJ
BJ (3-pin modified SMB/DO-214AA J-Bend)
R (Embossed Tape Reeled)
TISP3xxxT3BJR
TISP3xxxT3BJR-S
Insert xxx value corresponding to protection voltages of 070, 080, 095, 115, etc.
*RoHS Directive 2002/95/EC Jan 27 2003 including Annex
SEPTEMBER 2001 - REVISED FEBRUARY 2005
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.