MODEL: TC10EM
47 – 66 Hz)
Temperature Controller TC10 Series
RELATED PRODUCTS
TEMPERATURE CONTROLLER
(Modbus, 5 digit, LED display type, size 96 x 96 mm)
Functions & Features
• PC configurator software (model: TC10CFG)
Downloadable at M-System’s web site.
A dedicated cable is required to connect the module to the
PC. Please refer to the internet software download site or
the users manual for the PC configurator for applicable
cable types.
• Two PID controllers*
• Universal input x 2 points, control output x 4 points,
discrete input x 2 points, clamp-on current sensor input x 2
points
• Clamp-on current sensor (model: CLSE)
(Used for detecting the heater wire break)
• 2 universal inputs configurable to T/C, RTD, DC current or
voltage independently
• Discrete inputs usable to switch PID bank or operation
mode
GENERAL SPECIFICATIONS
Construction: Panel flush mounting
• Control outputs configurable to MV, PV or alarm
• Clamp-on current sensor input enables to detect heater
wire break or over current
Degree of protection: IP65; applicable to the front panel of
the unit with single mounting according to the specified
panel cutout
• Auto tuning function
*Only single loop control is available while loop 1 remote SP
is enabled.
Configuration jack: 2.5 dia. miniature jack connector;
RS-232-C level
Connection: M3 separable screw terminal (torque 0.5 N·m)
Solderless terminal: Refer to the drawing at the end of the
section.
96(3.8)
Recommended manufacturer: Japan Solderless Terminal
MFG.Co.Ltd, Nichifu Co.,ltd
Applicable wire size: 0.25 to 1.65 mm
2
(AWG 22 to 16)
96(3.8)
Screw terminal: Nickel-plated steel
Housing material: Flame-resistant resin (black)
Isolation: Pv1 to Pv2 to CT1 or CT2 to Di1 or Di2 to MV1 or
MV2 to Do1 or Do2 to Modbus to power
CT Input waveform
108(4.25)
mm (inch)
RMS sensing: Up to 15 % of 3rd harmonic content
Control mode: Standard PID, heating and cooling control
(ON/OFF, PID)
MODEL: TC10EM–[1]–M2
Proportional band (P): 0.1 to 3200.0 (temperature unit)
Integral time (I): 0 to 3999 sec.
ORDERING INFORMATION
• Code number: TC10EM-[1]-M2
Specify a code from below for [1].
(e.g. TC10EM-A-M2)
Derivative time (D): 0.0 to 999.9 sec.
Auto-tuning: Limit cycle method
Alarm: Deviation high & low, absolute high & low, etc.
Sampling cycle: 100 msec.
Control cycle: 1.0 to 99.9 sec.
[1] CONTROL OUTPUT
A: 0 – 20 mA DC (Load resistance 500 Ω max.)
Open-collector 2 points
(100 msec. fixed for Mv output 0 - 20 mA DC
and 0 - 10 V DC)
Mv output range: -5 - +105 % for output scale
Parameters: Stored in non-volatile memory; write/erase
cycle endurance: less than 1 000 000
Parameter setting: With front panel operation buttons or PC
configurator software (model: TC10CFG)
• Universal input
V: 0 – 10 V DC (Load resistance 2 kΩ max.)
Open-collector 2 points
P: 12 V pulse (Load resistance 600 Ω max.)
Open-collector 2 points
• Burnout
POWER INPUT
AC Power
• Control output
• Loop
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
TC10EM SPECIFICATIONS
ES-9581 Rev.4 Page 1/7
http://www.m-system.co.jp/