SN74AXC8T245-Q1
SCES892B – NOVEMBER 2018 – REVISED MAY 2021
SN74AXC8T245-Q1 Automotive 8-Bit Dual-Supply Bus Transceiver With Configurable
Voltage Translation and Tri-State Outputs
The SN74AXC8T245-Q1 device is designed for
asynchronous communication between data buses.
1 Features
•
•
AEC-Q100 qualified for automotive applications
Qualified fully configurable dual-rail design allows
each port to operate with a power supply range
from 0.65 V to 3.6 V
Operating temperature from –40°C to +125°C
Multiple direction-control pins to allow
simultaneous up and down translation
Up to 380 Mbps support when translating from 1.8
V to 3.3 V
VCC isolation feature to effectively Isolate both
bses in a power-down scenario
Partial power-down mode to limit backflow current
in a power-down scenario
The device transmits data from the A bus to the B bus
or from the B bus to the A bus, depending on the logic
level of the direction-control inputs (DIR1 and DIR2).
The output-enable (OE) input is used to disable the
outputs so the buses are effectively isolated.
•
•
The SN74AXC8T245-Q1 device is designed so the
control pins (DIR and OE) are referenced to VCCA
.
•
•
•
This device is fully specified for partial-power-down
applications using Ioff. The Ioff circuitry disables
the outputs when the device is powered down.
This inhibits current backflow into the device which
prevents damage to the device.
•
•
Compatible with SN74AVC8T245-Q1 level shifter
Latch-up performance exceeds 100 mA per JESD
78, class II
The VCC isolation feature ensures that if either VCC
input supply is below 100 mV, all level shifter outputs
are disabled and placed into a high-impedance state.
2 Applications
To ensure the high-impedance state of the level shifter
I/Os during power up or power down, OE should be
tied to VCCA through a pullup resistor; the minimum
value of the resistor is determined by the current-
sinking capability of the driver.
•
•
•
•
Infotainment head unit
ADAS fusion
ADAS front camera
HEV battery management system
Device Information
3 Description
PART NUMBER(1)
PACKAGE
BODY SIZE (NOM)
4.40 mm × 7.80 mm
3.50 mm × 5.50 mm
3.50 mm × 5.50 mm
The SN74AXC8T245-Q1 AEC-Q100 qualified device
is an 8-bit non-inverting bus transceiver that resolves
voltage level mismatch between devices operating at
the latest voltage nodes (0.7 V, 0.8 V, and 0.9 V) and
devices operating at industry standard voltage nodes
(1.8 V, 2.5 V, and 3.3 V) and vice versa.
SN74AXC8T245QPWRQ1 TSSOP (24)
SN74AXC8T245QRHLQ1 VQFN (24)
SN74AXC8T245QRGYQ1 VQFN (24)
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
The device operates by using two independent power-
supply rails (VCCA and VCCB) that operate as low as
0.65 V. Data pins A1 through A8 are designed to track
VCCA, which accepts any supply voltage from 0.65 V
to 3.6 V. Data pins B1 through B8 are designed to
track VCCB, which accepts any supply voltage from
0.65 V to 3.6 V.
3.3 V
1.5 V
Processor
VCCA DIR1 DIR2
VCCB
B1
Power Management
A1
A2
A3
A4
Control Block
B2
B3
B4
B5
B6
B7
B8
SN74AXC8T245-Q1
Data Block
Interrupts
Register Map
Sensor Block
A5
A6
A7
A8
GND
GND
Typical Application Schematic
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.