SN54ACT574, SN74ACT574
OCTAL D-TYPE EDGE-TRIGGERED FLIP-FLOPS
WITH 3-STATE OUTPUTS
SCAS537D – OCTOBER 1995 – REVISED NOVEMBER 2002
SN54ACT574 . . . J OR W PACKAGE
SN74ACT574 . . . DB, DW, N, NS, OR PW PACKAGE
(TOP VIEW)
4.5-V to 5.5-V V
Operation
CC
Inputs Accept Voltages to 5.5 V
Max t of 9 ns at 5 V
pd
Inputs Are TTL-Voltage Compatible
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
OE
1D
2D
3D
4D
5D
6D
7D
8D
V
CC
1Q
2Q
3Q
4Q
5Q
6Q
7Q
8Q
CLK
description/ordering information
These 8-bit flip-flops feature 3-state outputs
designed specifically for driving highly capacitive
or relatively low-impedance loads. The devices
are particularly suitable for implementing buffer
registers, I/O ports, bidirectional bus drivers, and
working registers.
GND
The eight flip-flops of the ’ACT574 devices are
D-type edge-triggered flip-flops. On the positive
transition of the clock (CLK) input, the Q outputs
are set to the logic levels set up at the data (D)
inputs.
SN54ACT574 . . . FK PACKAGE
(TOP VIEW)
A buffered output-enable (OE) input can be used
to place the eight outputs in either a normal logic
state (high or low logic levels) or the
high-impedance state. In the high-impedance
state, the outputs neither load nor drive the bus
lines significantly. The high-impedance state and
the increased drive provide the capability to drive
bus lines in a bus-organized system without need
for interface or pullup components.
3
2
1
20 19
18
4
5
6
7
8
3D
4D
5D
6D
7D
2Q
3Q
4Q
5Q
6Q
17
16
15
14
9 10 11 12 13
OE does not affect internal operations of the flip-flop. Old data can be retained or new data can be entered while
the outputs are in the high-impedance state.
To ensure the high-impedance state during power up or power down, OE should be tied to V through a pullup
CC
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
ORDERING INFORMATION
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
†
PACKAGE
T
A
PDIP – N
Tube
SN74ACT574N
SN74ACT574N
Tube
SN74ACT574DW
SN74ACT574DWR
SN74ACT574NSR
SN74ACT574DBR
SN74ACT574PWR
SNJ54ACT574J
SOIC – DW
ACT574
Tape and reel
Tape and reel
Tape and reel
Tape and reel
Tube
–40°C to 85°C
SOP – NS
SSOP – DB
TSSOP – PW
CDIP – J
ACT574
AD574
AD574
SNJ54ACT574J
SNJ54ACT574W
SNJ54ACT574FK
–55°C to 125°C
CFP – W
Tube
SNJ54ACT574W
SNJ54ACT574FK
LCCC – FK
Tube
†
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2002, Texas Instruments Incorporated
UNLESS OTHERWISE NOTED this document contains PRODUCTION
DATA information current as of publication date. Products conform to
specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all
parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265