CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Radial Lead Type, Long Life Assurance
PLX
Radial lead type:
Lead free flow soldering condition correspondence.
High reliability, High voltage (to 50V).
Low ESR, High ripple current.
Long life of 3000 hours at 125°C.
PLX
Adapted to the RoHS directive (2011/65/EU).
Higher
Temperature
PLV
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Tangent of loss angle (tan δ)
–55 to +125°C
16 to 50V
22 to 390µF
20% at 120Hz, 20°C
Less than or equal to the specified value 120Hz, 20°C
at
(
1)
ESR
Less than or equal to the specified value 100kHz, 20°C
at
Leakage Current ( 2)
Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+125°C / Z+20°C 1.25
Z–55°C / Z+20°C 1.25
(100kHz)
( )
3
Capacitance change
Within 20% of initial value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 3000 hours at 125°C.
150% or less of the initial specified value
150% or less of the initial specified value
Less than or equal to the initial specified value
tan δ
Endurance
(
1)
ESR
Leakage current ( 2)
( )
3
Capacitance change
Within 20% of initial value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Damp Heat
150% or less of the initial specified value
150% or less of the initial specified value
Less than or equal to the initial specified value
tan δ
(
1)
ESR
(Steady State)
Leakage current ( 2)
After soldering the capacitor under the soldering conditions
prescribed here as preheat at 150 to 200°C for 60 to 180 seconds
and peak temperature at 265°C for 10 seconds or less, the
capacitor shall meet the specifications listed at right, provided that
its temperature profile is measured at both of terminal ends facing
the soldering side.
( )
3
Capacitance change
Within 10% of the initial capacitance value
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
tan δ
Resistance to
Soldering Heat
(
1)
ESR
Leakage current ( 2)
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 35V 39 F)
µ
Resin coated Case
Capacitance
1
2
3
4
5
6
7
8
9
10 11 12
Voltage(V:35V)
P L X 1 V 3 9 0 M
C L 1
Size code
Configuration
Capacitance tolerance ( 20%)
Rated capacitance (39µF)
Rated voltage (35V)
Series name
φd
Series
Lot. No.
+0.5MAX.
15MIN
4MIN
L
Type
(mm)
13L
10.0
12.5
5.0
φ8 × 9L φ8 × 12L φ10
×
Size
φD
L
P
φd
8.0
8.5
3.5
0.6
8.0
11.5
3.5
Voltage
V
16
20
D
25
E
35
V
50
H
Code
C
0.6
0.6
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
60
CAT.8100E
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
