MSS-MH SERIES
125 WATT
DC/DC CONVERTERS
FEATURES
120/270 VOLT
INPUT
• Internal EMI filter meets
MIL-STD-461E CE102,
and MIL-STD-461C CE03
• Wide 5:1 input range:
80 to 400 VDC
• Output voltage adjustable to
include 3.3, 5, 15, and 28
• Operating temp. (baseplate)
100% power –55°C to +100°C
Derate to 0% power at 130°C
• Sync, inhibit and
Size (typ.): 4.60 x 2.40 x 0.55 inches
(116.8 x 61.0 x 14.0 mm)
Weight:
300 grams maximum
remote sense functions
• Magnetic isolated feedback
• Up to 89% efficiency
MODELS
V OUT Pre-Set V OUT Adjust*
MODEL
MSS-MHL
MSS-MHH
MSS-MH28
6
18
28
2.5 to 6.4
6 to 19.3
24 to 30.0
*Please see “Output Voltage Adjust” Figures 2 and 3.
DESCRIPTION
Interpoint’s 125 watt MSS-MHL, MHH, and MH28 DC/DC converters
are the first models in a new series of high reliability DC/DC
converters. A built in EMI filter compliant to MIL-STD-461E, CE102
and MIL-STD-461C CE03, plus an output filter eliminate the need
for additional modules or components. With an 80 to 400 VDC input,
a 2.5 to 6 VDC output, and a wide operating temperature range of
–55° to +100°C, the MSS-MHL is well suited for aerospace, auto-
motive, commercial, and industrial applications. The trimmable
output can provide 5 VDC for current or older applications while the
same device can later be trimmed to 3 or 2.5 VDC to accommodate
newer voltage requirements. Typical efficiency ranges from 79% to
82%. Two screening levels are available—standard and ST—
offering varying levels of temp cycle, burn-in, and electrical test.
Please see Table 1 for screening information.
CE102 and CE03. Each converter switches at a fixed frequency of
520 kHz typical. There is a protection circuit for input overshoot
during input power fast turn-on. This design uses a current mode
control method with a feedback transformer that provides isolation
between input and output.
SYNC, INHIBIT, REMOTE SENSE, AND V OUT ADJUST
Sync in, sync out, inhibit, and remote sense are additional controls
to enhance converter performance. Sync in, sync out, and inhibit are
referenced to control return (Ctrl Rtn, pin 7). The converters can be
synchronized to an external clock using the sync in terminal (pin 9).
Two or more converters can be synchronized by using the sync out
terminal (pin 6) which helps reduce interference and the possible
generation of beat frequencies. The sync terminals can be left
unconnected when not used.
The MSS Series™ converters offer three output voltage ranges. The
high input voltage of 80 to 400 VDC encompasses 120 volt and 270
volt busses. The three output voltage choices of 2.5 to 6, 6 to 18
and 24 to 28 cover the newer low voltage requirements; the stan-
dard 5 volt requirements; plus the 12, 15, 24, and 28 volt require-
ments of distributed power.
The converter operates normally when the Inhibit terminal (pin 8) is
left open or connected to an open collector interface. Pulling the
inhibit low disables switching and results in no output and a low 5
mA input current.
The remote sense terminals (pins 3 and 4) can be connected at the
load to minimize line voltage drops, maintaining the desired output
voltage directly at the load. If not used, the sense terminals should
be connected to their respective Vout terminals (pins 1 and 2).
INPUT AND OUTPUT FILTERING: LOW NOISE
All converters have an integrated input EMI filter and output filter.
The MSS 125 watt series, in a package 4.6 x 2.4 x 0.55 inches
(116.8 x 61.0 x 14.0 mm), replaces an industry standard configura-
tion of three half bricks (input filter, converter, and output filter). The
EMI filter meets the conducted emission requirements of MIL-STD-
461E, CE102 and MIL-STD-461C CE03. The output filter keeps the
Vout can be adjusted down using the trim pin or adjusted up using
the sense pins. Please see Figures 2 and 3 for Vout tables.
output ripple to
MHz to 20 MHz and 12 mV peak-to-peak from 10 kHz to 2 MHz.
a
typical of 75 mV peak-to-peak from
2
CONVERTER CONSTRUCTION/PACKAGING
MSS Series converters are constructed from surface mount compo-
nents soldered to a printed circuit board. The PCB is attached to a
lightweight, metal matrix composite, baseplate which provides the
high thermal conductivity of aluminum but has the advantage of a
low Coefficient of Thermal Expansion (CTE) and higher strength. A
potting compound is used to enhance the assembly’s ability to meet
harsh environmental requirements.
OPERATION
The MSS Series DC/DC converters use a boost converter followed
by a forward converter to achieve the wide 5 to 1 input voltage range
(80 to 400 VDC) and a 3 to 1 output ranges (2.5, 6 or 28VDC). The
boost stage provides low input noise and extra filtering for the 200
to 400 volt input range. The EMI filter provides both differential and
common mode rejections in a wide frequency range to meet both
1
5秒后页面跳转
英伟达新AI芯片Rubin或提前半年亮相
苹果iPhone 17将全系采用三星/LG显示LTPO OLED面板
三星深化印度制造布局，供应链本地化进程加速
芯擎科技“星辰一号”自动驾驶芯片点亮成功，2025年量产在即
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
